|
|
Audi 80/90/CoupeSince 1986-1991 of releaseRepair and car operation |
|
|
Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburettors 3. Greasing system + 4. Cooling system + 5. Fuel system + 6. An exhaust system + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system + 11. A steering + 12. A body, salon + 13. A central air + 14. An electric equipment |
3. Greasing system
|
| THE GENERAL DATA |
|
|
| 1. A stopper маслозаливной mouths 2. A lining 3. An oil atomizer for piston cooling 4. 10 Н.м., grease with fixing structure AMV188 100 02 5. A ring lining 6. A tube маспоприемника 7. A lining of the oil pallet To grease with gluing structure At installation it is not supposed 8. The oil pallet, for removal it is necessary: спить oil to establish the adaptation 10-222 to remove an engine mudguard, to remove the protective panel of the pallet 9. A drain stopper of the oil pallet 10. A sealing ring 11. 25 Н.м. 12. The cover of the oil pump – on a cover is available редукционный the valve 13. Gear wheels of the oil pump Width of a gear wheel of 36 mm 14. 20 Н.м. 15. 10 Н.м. |
16. The gauge of emergency pressure of oil with a threshold of operation 0,3. атм (brown colour) 25 Н.м. 17. The oil filter – turn on a special key 18. 25 Н.м. 19. Маслоохладитель – before installation grease a condensed surface with structure AMV188 100 02, check up a backlash with engine details 20. A ring lining 21. A sealing ring 22. A lining 23. 25 Н.м. 24. The case of the oil filter 25. Sealing rings 26. The display contact gauge of pressure of oil 1,8 атм (white colour), 25 Н.м. 27. Шестигранная заглушка or the gauge of the index of temperature of oil – the moment of an inhaling 10 Н.м. 28. The directing plug oil probeа 29. Oil probe |
| The new pump – 0,05 mm Limiting backlash – 0,20 mm |
| Limiting люфт – 0,15 mm |
Fill in oil, only with marks SF
In – all-weather oil
With – seasonal oil
Refuelling volume with the oil filter – 3,0 l
Without the oil filter – 2,5 l
Успокоитель – removal / installation
| The moment of an inhaling 350 Н.м. Bolt успокоителя, tighten a face key with the extension piece 2079 Put on surfaces of a female thread and a bolt carving anticorrosive structure AVM 188 001 02 |
| Turn away two bolts of fastening (are specified by arrows) |
|
1. The oil filter | 8. 40 Н.м. 9. A sealing ring Replace necessarily 10. 25 Н.м. 11. The bottom cover of a flywheel 12. 20 Н.м. 13. The contact gauge of pressure of oil (white colour) The moment of an inhaling 25 Н.м. 14. The gauge of emergency pressure of oil with a threshold of operation 0,3 атм (brown colour) The moment of an inhaling 25 Н.м. 15. Sealing washers Replace necessarily 16. Oil probe The difference of levels between two labels corresponds to volume of oil of 1,0 l |
| 1. A conducted gear wheel of a cam-shaft At replacement of a gear belt watch for Correctness of installation of a gear wheel 2. 80 Н.м. 3. A cover of a belt of a drive of a cam-shaft (top) 4. A gear belt of a drive of a cam-shaft 5. 10 Н.м. 6. A cover of a belt of a drive of a cam-shaft (bottom) 7. 10 Н.м. 8. 350 Н.м. 9. Успокоитель 10. A directing pulley Remove the adaptation 3034 11. 10 Н.м. 12. An epiploon Remove the adaptation 320.3 Before installation slightly grease the worker And external edges Establish оправкой from the complete set Adaptations 2080А запрессовывайте against the stop оправкой a press From the complete set of adaptations 2080А |
13. The reduktsionyyj valve The moment of an inhaling 40 Н.м. Operation threshold 5,3–6,3 атм. 14. 10 Н.м. 15. The oil pump It is replaced only in gathering watch correctness of installation under the relation To коленвалу 16. 10 Н.м. 17. A lining 18. ориентадионная a label "triangle" specifies gear wheels of the oil pump Aside предней covers 19. 20 Н.м. 20. A cover drive a belt (back) 21. Remote plugs 22. 10 Н.м. 23. 20 Н.м. |
Fill in oil, only with marks SF
In – all-weather oil
With – seasonal oil
Refuelling volume with the oil filter – 3,5 l
Without the oil filter – 3,0 l
The oil pump and components of a gear belt of a drive (Compartment model)
| 1. The moment of an inhaling 10 Н.м. 2. The moment of an inhaling 65 Н.м. 3. A conducted gear wheel of a cam-shaft At installation of a belt of a drive, pay attention on ориентационную a label 4. A gear belt of a drive of a cam-shaft 5. A cover drive a belt (back) 6. A cover drive a belt (top) 7. Remote plugs 8. The moment of an inhaling 10 Н.м. 9. A cover drive a belt (bottom) 10. Успокоитель 11. A bolt успокоителя, tighten with the moment 350 Н.м., using the extension piece 2079 and a face key 2084 |
12. An epiploon 13. The reduktsionnyj valve and the gauge of temperature of oil Pressure of operation of the valve from 5 to 8 атм. 14. A roller натяжителя 15. The oil pump It is replaced only in gathering At installation watch position of an adjusting pin коленвала 16. Gear wheels of the oil pump The triangular label is turned towards a cover 17. A lining |
| 1. A stopper маслозаливной mouths At lining damage, replace 2. The oil filter Turn on by means of a special key Turn manually Familiarise with the instruction on the filter case 3. The gauge of emergency pressure of oil The moment of an inhaling 6 Н.м Turn on fixing structure D6 4. An adapter The moment of an inhaling 50 Н.м. 5. A lining Landing to gluing structure is not supposed 6. The moment of an inhaling 10 Н.м. 7. A clamp, replace |
8. The moment of an inhaling of bolts М6 – 10 Н.м., Bolts М8 – 20 Н.м. 9. Oil probe for check of level of oil 10. The display contact gauge of pressure of oil on 1,8 атм (white colour) The moment of an inhaling 25 Н.м. 11. The contact gauge of emergency pressure of oil on 0,3 атм (brown colour) The moment of an inhaling 25 Н.м. 12. A tube маслоприемника 13. The moment of an inhaling of bolts 10 Н.м. 14. A partition 15. The oil pallet Before installation clear contact planes 16. A lining Replace 17. The moment of an inhaling 30 Н.м. |