|
|
Audi 80/90/CoupeSince 1986-1991 of releaseRepair and car operation |
|
|
Audi 80/90/Coupe + 1.2. Car identification + 2. Engines, carburettors 3. Greasing system + 4. Cooling system + 5. Fuel system - 6. An exhaust system 6.1. Exhaust system components + 7. Ignition system + 8. Transmission + 9. Suspension brackets, wheels + 10. Brake system + 11. A steering + 12. A body, salon + 13. A central air + 14. An electric equipment |
6. An exhaust system
|
| THE GENERAL DATA |
|
1. A tube for measurement WITH
2. A cap of a tube for measurement WITH 3. 25 Н.м. 4. A final collector 5. 30 Н.м. 6. Consolidation Always replace 7. 35 Н.м. 8. 40 Н.м. 9. The average muffler Average and back mufflers are established at factory as a uniform detail, spare average and back mufflers are delivered separately together with tightening муфтой 10. A fixing ring Preliminary tightness: approximately 7мм Pay attention to arrows in вкладке And 11. Depth of introduction "and" should be at least 42.5 mm 12. Tightening муфта 13. 40 Н.м. 14. Fixing rings Preliminary tightness: about 12 mm 15. The back muffler |
16. A place of a cut for replacement It is marked by cuts (3) on a circle of a connecting pipe Cut a pipe at right angle to a pipe axis In the established position the cut can be made a chain saw The cut can be made also, having removed system To remove an exhaust system, ослабьте a clip ahead of the average muffler and fastening of the left bottom shock-absorber, also lower a back axis 17. Tightening муфта 18. 40 Н.м. 19. The Katalitichesky converter 20. A tube for measurement WITH 21. The oxygen gauge (50 Н.м.) Cover a carving with structure G5 Do not allow G5 to get to cuts on the gauge case 22. A basic arm It is attached to transmission 23. 25 Н.м. 24. An exhaust pipe |
1. 20 Н.м. 14. 25 Н.м.
Exhaust system, arrangement of components (5-cylinder models)
2. 30 Н.м.
3. 25 Н.м.
4. A final collector
5. Consolidation
6. 35 Н.м.
7. 25 Н.м.
8. A spring
9. A sealing ring
Always replace
10. Tightening муфта
Depth of introduction "and" should be at least 42.5 mm
11. Fixing rings
Preliminary tightness: about 7 mm
Pay attention to arrows in вкладке And
12. The average muffler
13. The back muffler
Average and back mufflers are established at factory as a uniform detail, spare average and back mufflers are delivered separately together with tightening муфтой
14. A fixing ring
Preliminary tightness: about 12 mm15. A place of a cut for replacement
It is marked by cuts (3) on a circle of a connecting pipe
Cut a pipe at right angle to a pipe axis
In the established position the cut can be made a chain saw
The cut can be made also, having removed system
To remove an exhaust system, ослабьте a clip ahead of the average muffler and fastening of the left bottom shock-absorber, also lower a back axis
16. 40 Н.м.
17. 40 Н.м.
18. Tightening муфта
19. The Katalitichesky converter
20. The oxygen gauge (50 Н.м.)
Cover a carving with structure G5
Do not allow G5 to get to cuts on the gauge case
21. A basic arm
It is attached to transmission
22. A forward exhaust pipe
23. A tube for measurement WITH
Exhaust system, arrangement of components (Compartment model)
1. A lining
Replace
2. 10 Н.м.
3. The heat-shielding screen
4. 25 Н.м.
5. A tube for measurement WITH
6. 30 Н.м.
7. A final collector
8. The oxygen gauge (50 Н.м.)
9. Ring consolidation, replace
10. The Katalitichesky converter 11. Tightening муфта
12. Fixing rings
At replacement make sure that new rings correspond to the old
13. The back muffler
14. A forward exhaust pipe
15. Fixing rings
At replacement make sure that new rings correspond to the old
16. The central muffler
Exhaust system, arrangement of components for all-wheel drive (4х4) models
2. 30 Н.м.
3. 25 Н.м.
4. A final collector
5. Consolidation
6. 35 Н.м.
7. 25 Н.м.
8. A spring
9. A sealing ring
10. 40 Н.м.
11. A fixing ring
12. The average muffler
13. A sealing ring
Always replace 14. 25 Н.м.
15. A fixing ring
Preliminary tightness: about 12 mm
16. The back muffler
17. Tightening муфта
18. The Katalitichesky converter
19. The oxygen gauge (50 Н.м.)
Cover a carving with structure G5
20. A basic arm
It is attached to transmission
21. A forward exhaust pipe
22. A tube for measurement WITH
The prevention
Exhaust system, arrangement of components for 20-klapannnyh models
2. A hose to a heater of soaked up air
3. The heat-shielding screen
4. A tube for measurement WITH
5. The valve recycling exhaust gases (РВГ)
6. Vacuum tube РВГ
7. Bolts "банджо", 20 Н.м.
9. A final cranked branch pipe
10. The main pipe
11. 30 Н.м.
12. A fixing ring
Preliminary tightness: about 8 mm
13. The jet muffler
15. 30 Н.м.
16. The oxygen gauge, 50 Н.м.
Cover a carving with structure G5, but do not allow structure to get to cuts on the gauge case
17. 20 Н.м.
18. The Katalitichesky converter
19. 25 Н.м.
20. A sealing washer, 20 Н.м.
21. Tightening муфта, 40 Н.м.
22. 25 Н.м.
23. Tightening муфта, 40 Н.м.
24. The back muffler
Vacuum connections (Compartment model)
1. Return топливопровод
2. Submitting топливопровод
3. A head of cylinders
4. Ventilating hoses картера
5. To the device of blocking of differential
6. The throttle case
7. A cover of soaked up air
8. Дозатор air 9. The coal filter
10. A pressure regulator
11. The zapornyj valve
12. The electromagnetic valve of the coal filter
13. An inlet collector
14. The valve of stabilisation of idling
15. The air filter
Vacuum connections (model) Audi-90
1. The electromagnetic valve (N 80) for the coal filter
2. The throttle case
3. Valve RVG
4. A fuel injector
5. The zapornyj valve
6. Ventilation картера
7. To the fuel tank
8. The fuel distributor
9. From the fuel filter
10. An inlet collector
11. The valve of stabilisation of idling
12. A head of cylinders
13. Vacuum connection of the amplifier of brake system 14а. Заглушка (cars with a forward drive without the conditioner)
14b. Connections of the conditioner or differential blocking
14с. Connections of blocking of differential (all-wheel drive cars with the conditioner)
14d. Conditioner connection (all-wheel drive cars with the conditioner)
15. The vacuum tank
16. Frequency valve RVG (N 121)
17. The coal filter