Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Systems of start, ignition
- 9. Transmission
   + 9.1.2. Technical characteristics
   + 9.2. A Mehnichesky transmission
   - 9.3. An automatic transmission
      9.3.2. Technical characteristics
      9.3.3. Removal and installation automatic gearbox
      9.3.4. Partition automatic gearbox
      9.3.5. A rope of the lever of a gear change
      9.3.6. Evident repair of a transmission 097
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice


https://www.youtube.com/channel/UCoah5uA-uF-j35-MalVTfRQ


9.3.5. A rope of the lever of a gear change
THE GENERAL DATA

The gear change lever 01N

1. A rubber cover
2. A clamp
3. A bolt
4. A basic arm
5. A nut
6. The locking valve
The switching lever
7. A bolt
8. A spring
9. The plug
10. A bolt
11. The ignition switch
12. A locking rope
13. A cover
14. A bolt
15. The handle
16. A bolt
17. A lever casing
18. The switching lever
19. A pin
20. A spring
21. The plug
22. A lock ring
23. A washer
24. An arm
25. The plug
26. A spring clip
28. The lever
29. A nut
30. A washer
31. A ring
32. The plug
33. A ring
34. A washer
35. A sleeve
36. A pin
37. A rubber cover
38. A nut and a directing tube
39. A washer
40. The plug
41. A washer
42. A sealing ring
43. A rope
44. The plug
45. A washer
46. A nut

In models 097 the locking rope connects the lever of a gear change and the ignition lock.

TRANSMISSIONS 01N AND 097

Removal

PERFORMANCE ORDER
1. Establish the gear change lever in neutral position.
2. Lift and fix a forward part of the car.
3. Remove теплоизолирующий the screen from an arm of the mechanism of a gear change.
4. Disconnect a rope of the lever of a gear change from a transmission.
5. In models 01N braid a nut and a bolt in a back part of the right support of a transmission.
6. Remove the right basic arm of a transmission.
7. In models 01N let out till June 1995 г, remove a clip and squeeze out the plug from the basis of the lever of switching.
8. Remove the central console.
9. Remove the mechanism of the lever of a gear change.
10. Loosen the a lock nut also disconnect an internal rope.
11. Shift a rubber cover and remove from a rope a nut and directing tube.
12. Disconnect a rope from a back cover of the mechanism of the lever of switching.

Installation

Installation is made in sequence, return to removal.

Adjustment

PERFORMANCE ORDER
1. Establish the gear change lever in parking () position.
2. Establish switching lever on a transmission in parking position.
3. Be convinced that the rope is not overwound and not compressed. Tighten a tightening nut.
4. Check up work of the lever of a gear change.
5. Establish the lever in position (R), check up with the help probeа that the backlash between the locking electromagnetic valve and the lever was within 0,6-1,4 mm (). If necessary adjust valve position.

LOCKING ROPE OF THE TRANSMISSION 097

Removal

PERFORMANCE ORDER
1. Remove the central console.
2. Remove a wheel and the instrument panel.
3. Establish the gear change lever in position (N).
4. Unscrew a bolt, крепящий a rope to the lever mechanism.
5. Uncover the lock of ignition and disconnect a rope clip.
6. Disconnect a rope from the ignition lock.

Installation

Installation is made in sequence, return to removal.

Adjustment

PERFORMANCE ORDER
1. Include ignition.
2. Loosen the an adjusting bolt (1) also adjust by means of measuring probeа a backlash between a shutter and a pin of the locking mechanism (A = 1,4–1,7 mm).
3. Check up mechanism work.

On the main page