Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
- 7. Transmission
   + 7.1. Coupling
   + 7.2. A mechanical drive of deenergizing of coupling
   + 7.3. A hydraulic drive
   + 7.4. A transmission
   - 7.5. A drive of forward wheels
      7.5.1. Полуось
      7.5.2. The internal hinge of equal angular speeds (SHRUS)
      7.5.3. The external hinge of equal angular speeds (SHRUS)
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment

7.5. A drive of forward wheels

7.5.1. Полуось
THE GENERAL DATA

Drive of a forward wheel

1 – a nut;
2 – полуось;
3 – a lock plate;
4 – a bolt;
5 – a washer;
6 – a cover

Model
Length of a semiaxis
The right
The left
With 4-cylinder engines:
  – With mechanical КП
579,20
540,70
  – With automatic КП
540,70
590,50
With 5-cylinder engines:
  – With mechanical КП
550,90
550,90
  – With automatic КП
529,10
582,80

Removal

PERFORMANCE ORDER
1. To brake the car a lay brake and to establish an emphasis under back wheels.
2. To weaken an inhaling of bolts of fastening of a forward wheel and to turn away a nut of 1 fastening of a semiaxis.
3. To raise and establish on a support a forward part of the car.
4. Definitively to turn away bolts of fastening and to remove a forward wheel.
5. On models with an automatic transmission to remove holders of pillows of the stabilizer of cross-section stability and to disconnect the stabilizer from a rotary fist.
6. To turn away bolts of 4 fastenings of an internal SHRUS to a flange of a semiaxis and to take out them with lock plates 3.
7. To shift полуось upwards, having disconnected it from a semiaxis flange.
8. To turn a steering wheel against the stop to the left at dismantle of the left semiaxis or to the right at dismantle of the right semiaxis.
9. Выпрессовать from a wheel nave шлицевую a part of a semiaxis by means of a stripper and to remove полуось from the car.

Installation

PERFORMANCE ORDER
1. To clear of a dirt and the rests of special glue шлицы naves and semiaxes and to wipe their gasoline.
2. To put special glue D6 on шлицы to a semiaxis (only on models of release till January, 1988 and on models with an automatic box) for the length of 5-6 mm from an end face шлицевой to a part. After that the trial trip can be made only through 60 mines to allow to glue to harden.
3. To insert полуось into a wheel nave.
4. To connect полуось to a flange and to wrap bolts of fastening М10 with lock plates the moment 80 Н·м (8,0 кгс·м) or М8 – the moment 45 Н·м (4,5 кгс·м).
5. On models with an automatic transmission to connect the stabilizer of cross-section stability.
6. To establish a wheel and наживить fastening bolts.
7. Наживить a new nut of fastening of a nave (on models of release after January, 1988 – a special bolt).
8. To lower the car on wheels.
9. To tighten a nut the moment 280 Н·м (28,0 кгс·м). On models of release after January, 1988 to tighten a special bolt the moment 200 Н·м (20,0 кгс·м), and then to tighten on a turn quarter (90 °).
10. To tighten bolts of fastening of a wheel in regular intervals the moment 110 Н·м (11,0 кгс·м).


On the main page