Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

11.8. System of hydrostrengthening of a steering

THE GENERAL DATA

The pump of the hydraulic booster of a steering for 4-cylinder models

1. 20 Н.м. 2. An arm 3. 20 Н.м., always replace 4. An arm 5. 20 Н, m. 6. An arm 7. 20 Н.м. 8. A klinovoj belt, the size: 9.5 х850 mm 9. A bolt and a fixing nut 10. 20 Н.м. 11. A pulley, establish a mark "5Z" forward 12. 25 Н.м. 13. 20 Н.м. 14. The lopastnyj pump Before installation fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel

15. A bolt "банджо", the inhaling moment: 50 Km 16. A sealing ring Always replace 17. A soaking up hose 18. 19. A bolt "банджо", the inhaling moment: 50 Н.м. 20. A high pressure hose 21. An arm 22. 20 Н.м.

The pump of the hydraulic booster of a steering for 5-cylinder models

1. A bolt "банджо" The inhaling moment: 50 Н.м. 2. A sealing ring Always replace 3. 20 Н.м. 4. An arm 5. An arm 6. A klinovoj belt The size: 12.5x992мм 7. 20 Н.м. 8. A pulley Establish a mark "5Z" forward 9. 20 Н.м. 10. The tension device 11. 20 Н.м. 12. Самоконтрящаяся a nut The inhaling moment: 20 Н.м.

13. The hydraulic booster pump рулевего managements Before installation fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel 14. An arm 15. A high pressure tube 16. A sealing ring Always replace 17. A bolt "банджо", the inhaling moment: 45 Nanometers. 18. A soaking up hose 19. 20 Н.м. 20. A sealing ring

Tank of the hydraulic booster of a steering

1. A hose of the return pipeline 2. A collar 3. The tank is filled by a hydraulic liquid Check up liquid level in a tank (on marks On the tank) after the engine паработает during 2минут, wheels thus should stand directly Muffle the engine, check up level of a liquid and add to a mark the MOVE if it is necessary

4. A collar 5. A soaking up hose 6. The filter Clean a cleaning solution 7. A spring clamp It is put on on probe for measurement of level of a liquid 8. A spring 9. Уплотнительно a ring 10. A cover of a jellied aperture

The pump of system of hydrostrengthening of a steering

1. A lining plate * It is inserted into a lining 2. Прокладка* 3. A plate with apertures 4. A lock ring * 5. 15 Н.м. Grease with hermetic D6 before installation Longer end twists in the pump case 6. A shaft of the pump with a flange check up on presence of scratches and wear tracks If it is necessary, replace all pump Remove poтор and a shaft for Replacements of a sealing ring 7. Sealing кольцо* For replacement, it is necessary to disassemble the pump 8. The case Oil channels (are specified by an arrow) both halves of the case should coincide after assemblage 9. Sealing кольцо* 10. A rotor 11. Blades The polished surface (it is specified by an arrow) should be turned outside 12. Статор Installation position: the arrow on статоре should be visible after installation 13. A valve clamp аккумратно remove by means of small отверкти 14. The restrictive valve, do not assort 15. A spring 16. The case

The dual hydraulic pump for model with 20-klapannym the engine

1. A bolt for a tension клинового a belt 2. A clip 3. 20 Н.м. 4. A rotary arm 5. 20 Н.м. 6. З0Н.м. At untwisting or removal, always replace with a detail 100 067 04 7. A mobile arm 8. 20 Н.м. 9. 20 Н.м. 10. A klinovoj belt, the size: 12.5x992 mm 11. A pulley, establish a mark "5Z" forward

12. 10 Н.м. 13. The pump with two pistons Systems сервоусиления brakes 14. The lopastnoj pump Before installation, fill soaking up part with a hydraulic liquid and повращайте the pump that the liquid began to leave the target channel 15. The return pipeline, from a tee 16. The high pressure tube, goes to рейке a steering 17. 50 Н.м. 18. 20 Н.м. 19. 35 Н.м. 20. A high pressure tube