BMW 3 series E30

Since 1983-1994 of release

Repair and car operation



BMW E30
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   - 3.1.2. Specifications
      3.1.3. Kinds of the repair work which is carried out without dismantle of the engine
      3.1.4. An order of installation of the piston of 1st cylinder in ВМТ a compression step
      3.1.5. A cover of a head of cylinders
      3.1.6. A soaking up collector
      3.1.7. A final collector
      3.1.8. Covers of a chain of a drive of a cam-shaft (engine M10)
      3.1.9. A chain and asterisks (engine M10)
      3.1.10. Covers of a gear belt (engines M20 and М40)
      3.1.11. A gear belt and cam-shaft asterisks (engines M20 and М40)
      3.1.12. Forward epiploons
      3.1.13. A head of cylinders
      3.1.14. The pallet
      3.1.15. The oil pump
      3.1.16. A flywheel (a leading disk)
      3.1.17. A back epiploon коленвала
      3.1.18. Engine mount details
   + 3.2. Dismantle and engine major repairs
   + 3.3. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmissions
+ 9. Coupling
+ 10. Brake system
+ 11. A running gear
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice

3.1.12. Forward epiploons

Replacement

PERFORMANCE ORDER
Engine M10, cam-shaft epiploon
1. Remove the top cover of a chain.
2. Beat out an epiploon from the interior of a cover, having put a cover on wooden бруски.
3. Grease and запрессуйте a new epiploon with blows on оправке the suitable diameter, resting against an external part of an epiploon.
4. Further assemblage is carried out upside-down.
Engine M10, epiploon коленвала
5. Remove a pulley and успокоитель.
6. Accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get.
7. Clear an aperture under an epiploon, grease and запрессуйте a new epiploon with blows on оправке the suitable diameter, resting against an external part of an epiploon.
8. Further assemblage is carried out upside-down.
Engines M20 and М40, a cam-shaft epiploon
9. Remove a belt and a cam-shaft asterisk.
10. On engine M20 get the case of an epiploon from a head of cylinders, having turned away 2 screws and turning the case in both parties.
11. On engine M20 cautiously beat out an epiploon from the interior of the case, having put the case on wooden бруски.
12. On engine M40 accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get from a head of cylinders.
13. Grease working edges and an external surface of a new epiploon with universal greasing.
14. On engine M40 wrap up a neck of a shaft an adhesive tape and dress an epiploon.
15. Запрессуйте a new epiploon blows on оправке the suitable diameter, resting against an external part of an epiploon.
16. On engine M20 replace a sealant of the case of an epiploon and establish the case, tighten screws.
17. Further assemblage is carried out upside-down.
Engine M20, epiploons коленвала and an intermediate shaft
18. Remove a gear belt, pulleys коленвала and an intermediate shaft.
19. Remove a forward cover, having turned away bolts (including 3 bottom bolts with which the pallet fastens) and having opened consolidation by blows of a rubber hammer, accurately clear of the rests of consolidation and beat out an epiploon from the interior of a cover, having put a cover on wooden бруски.
20. Grease and запрессуйте a new epiploon with blows on оправке the suitable diameter, resting against an external part of an epiploon.
21. Establish a cover, having replaced a lining and having put hermetic RTV on condensed places and a joint of a cover with the pallet and the block of cylinders.
22. Further assemblage is carried out upside-down.
Engine M40, forward epiploon коленвала
23. Remove a gear belt and an asterisk.
24. Remove with коленвала segment шпонку.
25. Accurately hook an epiploon a screw-driver wrapped up by an adhesive tape and get. If the epiploon does not give in to removal drill apertures both screw screws-samorezy and get an epiploon for heads of screws.
26. Clear an aperture under an epiploon, grease and запрессуйте a new epiploon without warps with blows on оправке the suitable diameter, resting against an external part of an epiploon.
27. Further assemblage is carried out upside-down. Replace a gear belt.


On the main page