Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system and release
   + The power supply system - petrol models
   + The power supply system - diesel models
   - Systems of decrease in toxicity and release of the fulfilled gases
      Check of serviceability of functioning / of a condition and replacement of components of systems of decrease in toxicity of the fulfilled gases
      The Katalitichesky converter - the general information and safety measures
      System of release of the fulfilled gases - the general information, removal and installation
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

System of release of the fulfilled gases - the general information, removal and installation

Petrol models


System of release of the fulfilled gases equipped catalytic the converter of models

1 — the Katalitichesky converter
2 — Intermediate section with the preliminary muffler
3 — the Basic muffler

4 — Podpruzhinennye of a nut of a joint of a reception pipe with a final collector


System of release of the fulfilled gases of models without каталитического the converter

1 — Intermediate section with the preliminary muffler
2 — the Basic muffler

3 Podpruzhinennye of a nut of a joint of a reception pipe with a final collector

On cars considered in the present Management the 3-section system of release of the fulfilled gases (illustrations System of release of the fulfilled gases equipped catalytic the converter of models and System of release of the fulfilled gases of models without каталитического the converter see) is used. The shown schemes are characteristic for all lineup of cars Citroyon Xantia. All sections of a final path are connected among themselves by means of фланцевых joints. For fastening of a reception pipe to a flange of a final collector bolts with nuts are used, tightness of a joint is reached at the expense of the central sealing ring. The spherical form of interfaced surfaces of connection and use подпружиненных washers provide flexibility of a joint and mobility of sections of system concerning a final collector (see the left bottom insert illustrations). For connection of among themselves remained sections special collars with blooming rings are used (see Inserts "and" on illustrations).

On the models equipped catalytic with the converter, assemblage of the last is a part of forward section of a final path and is built in in a reception pipe of system of release of the fulfilled gases.

Posting of sections of system it is carried out by means of rubber basic rings.

Diesel models

On diesel models without каталитического the converter the two-section scheme (a reception pipe and final section) can be used. And, in a place of a joint of a reception pipe with catalytic the converter the broad chamber is provided. In the rest the system design does not differ from considered above applied on petrol engines. On accompanying illustrations components of fixture of a joint of a reception pipe of system of release of the fulfilled gases with турбокомпрессором are illustrated.

Nut (1), plate of a spring (2) and a spring (3 one of knots of fastening of a flexible joint of a reception pipe of system of release of the fulfilled gases with турбокомпрессором (a kind from under the car)


Joint of a reception pipe with турбокомпрессором (a kind from an impellent compartment)

On equipped catalytic the converter models the system consists of three sections: каталитического the converter, an intermediate pipe and an exhaust pipe. For converter fastening to a final collector the flexible joint, providing to system relative freedom of moving is used. Other sections fasten among themselves by means of collars with blooming rings.

On all length of section of system are suspended to arms on the bottom of the car by means of rubber rings.

Removal

The system of release of the fulfilled gases can act in film from the car посекционно. In view of features of position of a back cross-section beam system removal in gathering probably only after a detachment from it final section.

To make removal of system or its separate section it is necessary preliminary поддомкратить the car and to establish it on reliable props. Alternatively the car can be tired out on a platform or a viewing hole.

Reception pipe

 PERFORMANCE ORDER

1. Give nuts of bolts of fastening of a reception pipe to a final collector. Remove plates of springs and springs. Separate a pipe from a collector and take a sealing ring.
2. Release a coupling bolt of a collar of fastening of a reception pipe to intermediate/back section of system. Divide sections and take a reception pipe from under the car. Remove a blooming sealing ring.

Intermediate section with the preliminary muffler

 PERFORMANCE ORDER

1. Turn out coupling bolts of collars of fastening of an intermediate pipe to reception and final sections of system.
2. Remove intermediate section from pendant support and take it from under the car.

Final section with the basic muffler

 PERFORMANCE ORDER

1. Release a collar of fastening of an exhaust pipe to intermediate/reception section of system. Separate final section.
2. Remove an exhaust pipe with rubber подвесов support and take it from under the car.

Thermofilter ()

For fastening of thermofilters to the car bottom bolts and nuts are used various type. Removal of each of screens becomes possible only after dismantle of corresponding section of system of release of the fulfilled gases. If the screen acts in film only for the purpose of providing of access to the components located behind it, on some models will weaken only its fixture enough and slightly to lower a plate.

Installation

Installation of each of sections is made in an order, the return to an order of its dismantle. Pay attention to following moments:
   a) Before a joint of sections of system track, that interfaced surfaces фланцевых connections have been carefully cleared of corrosion traces;
   b) do not forget to check up a condition of rubber rings of pendant support, defective components replace;
   c) Interfaced surfaces of a flexible joint of a reception pipe and a final collector/turbokompressora before assemblage should be greased by refractory greasing;
   d) Before a fixture tightening make sure of correctness of placing of sections of system in rubber подвесах support. Any of system sections should not adjoin to components of a suspension bracket and кузовными car elements.


On the main page