Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
- 6. Transmissions
   + 6.1. A mechanical transmission
   - 6.2. Automatic transmission
      6.2.1. Specifications
      6.2.2. Transmission diagnostics
      6.2.3. A drive cable заслонки
      6.2.4. Draught of transmission
      6.2.5. The blocking switch
      6.2.6. System of fixing of transfers
      6.2.7. The lever of change of transfers
      6.2.8. Removal and transmission installation
   + 6.3. A distributing box
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes





6.2.8. Removal and transmission installation

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Get probe the index of level of a liquid.
3. Disconnect a cable throttle заслонки for what ослабьте adjusting nuts, deduce a cable from an arm and unhook from draught. Disconnect cable latches.
4. Remove average section.
5. On cars 4WD remove the lever of a distributing box for what get a lock ring.
6. Lift the car.
7. Remove the bottom guards, boxes stirring to removal.
8. Merge трансмиссионную a liquid, establish the pallet into place.
9. Turn away bolts of an arm and remove a branch pipe of the index of level of a liquid.
10. Disconnect semiaxes (subsection 7.8 see).
11. Remove a forward exhaust pipe.
12. Turn on corrugated накидную a nut and get a speedometer cable. Not допускеайте easings of a felt lining and washers.
13. Disconnect from transmission all sockets (the gauge of speed, the solenoid of the blocking, the blocking switch, etc.).
14. Disconnect a rod from the lever on transmission.
15. Disconnect from transmission the tubes conducting to a cooler.
16. Remove a starter and take wires aside.
17. On cars with the engine 5VZ-FE remove a cross-beam of the stabilizer of a suspension bracket.
18. Uncover the hydrotransformer.
19. Designate hydrotransformer position on a leading disk, turn on serially 6 bolts for what turn коленвал clockwise.
20. Establish under картер a jack (it is desirable the special cart). Turn away bolts of fastening of a shaft картера to a cross-beam (a photo at the left). Turn away bolts, raise transmission and remove a cross-beam (a photo on the right).
21. Substitute under the engine a jack and turn away bolts of fastening of transmission to the engine.
22. Displace transmission back and remove from directing pins. Fix the hydrotransformer on transmission.
23. On cars 4WD remove a distributing box.

Installation

PERFORMANCE ORDER
1. Be convinced that the hydrotransformer nave is in gearing with the pump.
2. Establish transmission on the cart and cautiously lift, keeping its horizontal position. Attach tubes of cooling of a liquid.
3. Turn the hydrotransformer and combine the labels put before removal.
4. Cautiously submit transmission to the engine and establish on directing pins.
5. Wrap bolts of fastening of transmission and tighten with the set moment.
6. Tighten bolts of fastening of the hydrotransformer.
7. Establish a cross-beam and tighten bolts and nuts.
8. Lower a shaft картера, having combined with apertures in a cross-beam, tighten bolts and nuts.
9. Further assemblage is carried out upside-down (fig. Automatic transmission (type А340) all-wheel drive cars see).

On the main page