|
|
Audi 100/A61990-1997 of releaseRepair and car operation |
|
|
Audi 100/A6 - 1. The maintenance instruction 1.2. The panel of devices Audi A6/A6 Avant, S6/S6 Avant 1.3. Alarm and control lamps + 1.4. Installation of seats 1.5. Electric window raiser 1.6. Steering wheel installation 1.7. The ignition lock 1.8. Switches 1.9. Lever switches of light 1.10. Screen wipers and washer 1.11. Heating and ventilation 1.12. The conditioner 1.13. Installation of external mirrors 1.14. Electric put external mirrors 1.15. The Podemno-sdvizhnaja panel of a roof 1.16. A folding cover of the refuelling hatch 1.17. An automatic transmission 1.18. The dynamic program of switching (DPS) 1.19. The spare or emergency program 1.20. Control lever positions 1.21. The device kick-down 1.22. Recommendations about driving 1.23. A combination of devices 1.24. Control lamps 1.25. Symbols of red colour (1 degree priority) 1.26. Symbols of yellow colour (2 degree priority) 1.27. The onboard computer 1.28. Switches 1.29. System of maintenance of constant speed 1.30. System of screen wipers and windscreen 1.31. The automatic conditioner 1.32. Vozduhovypusknye devices 1.33. A control panel an independent heater 1.34. Electronic blocking of differential (EDS) 1.35. The control of level of oil 1.36. The amplifier of steering drive / Servotronic, a regulator of a road gleam 1.37. Cooling system 1.38. A brake liquid 1.39. Colour designations of safety locks + 1.40. Replacement of lamps 1.41. Auxiliary tap 1.42. Realisation of the starting help 1.43. Car nameplate data 1.44. The 4-cylinder engine in volume of 1,8 l 1.45. The 4-cylinder engine in volume of 1,9 l 1.46. The 5-cylinder diesel engine 1.47. Recommended pressure in tyres + 2. Maintenance service + 3. Engines + 3.2. Diesel engines + 3.3. Removal and a partition of engines + 4. Cooling system + 5. Heating and ventilation + 6. Fuel system + 7. An exhaust system + 8. Systems of start, ignition + 9. Transmission + 10. Brake system + 11. Suspension brackets, a steering + 12. A body + 13. An electric equipment + 14. A good advice |
1.20. Control lever positions
At the included ignition in a combination of devices there is an indication of actual position of a control lever. On the given illustration position "Р" is shown. Р – lay blocking Driving wheels are blocked by means of kinematic communications. Lay blocking can use only after a car stop. For lever installation in position "Р" preliminary wring out it downwards. At switching "R" in position "Р" of it it is not necessary to do of position. For страгивания the lever of switching from position "Р" at the included ignition press a pedal of a brake and wring out the lever downwards. R – backing transfer Backing transfer can be included only after a stop of the car and at engine work in an idling mode. Before switching in position "R" wring out the lever downwards. At the included ignition and control lever installation in position "R" backing lanterns burn. N – neutral position (idling position) For страгивания a control lever from position "N" at speed less than 5 km/h, and also at the motionless car and the included ignition to press a brake pedal. D – a substantive provision at advance Automatic switching on raised and hill-climbing gears within four steps of a box is carried out depending on loading of the engine, speed and the movement program. In a movement mode, under certain conditions, happens more preferably temporarily to translate a control lever in one of more low described positions. 3 – position for movement on roads to hilly district The given position is recommended at frequent switching from 3 transfers on 2nd and back, at a control lever finding in the basic position "D". 4th transfer is blocked. Thanks to it the brake effect of the engine a little raises at the released pedal of an accelerator. 2 – position for movement in mountains This position of the lever approaches for overcoming of long descents and liftings. 3rd and 4th transfers are blocked. It allows to avoid useless switching on the raised transfers and to increase brake effect of the engine. 1 – position for overcoming of abrupt biases It is recommended for overcoming very much steep slopes and descents – especially at movement with the trailer. For inclusion wring out a control lever downwards. After inclusion the car moves only on 1st transfer. It reaches the maximum brake effect of the engine. At manual switching on hill-climbing gears it is possible to establish a control lever in positions "3", "2" and "1". However automatics will be switched only after becomes impossible разносное increase in turns of the engine. |
On the main page
|