Audi 100/A6

1990-1997 of release

Repair and car operation

Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
- 6. Fuel system
   + 6.1.2. Technical characteristics
   - 6.2. Multidot system of injection of fuel
      6.2.2. Technical characteristics
      6.2.3. The air filter
      6.2.4. An accelerator rope
      6.2.5. Elements of system of injection of fuel Motronic/Jetronic
      6.2.6. Elements of system of injection of fuel Digifant
      6.2.7. The fuel filter
      6.2.8. The fuel pump and the gauge of level of fuel
      6.2.9. A fuel tank
      6.2.10. Release of pressure from system of injection of fuel
      6.2.11. An inlet collector
      6.2.12. Check of system of injection of fuel
      6.2.13. Neetilirovannyj gasoline
   + 6.3. System of injection MPI/MPFI (6-cylinder engines)
   + 6.4. The power supply system of diesel engines
   6.5. The device of service of heating
   6.6. Diagnostics of malfunctions of system of heating
   6.7. The conditioner: not only "pluses", but also "minuses"
   6.8. Rules of service of the conditioner
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice

6.2.11. An inlet collector

THE GENERAL DATA

Elements of the top section of an inlet collector on engine AAR, AAN

1. The gauge throttle заслонки
2. A fixing arm
3. A connection socket
4. The electronic block of management
5. A connection socket
6. Fixing bolts
7. The case throttle заслонки
8. The blowing-off valve
9. The switch of system of idling
10. A lining
11. A fixing arm
12. A clip
13. The screw
14. The temperature switch
15. An inlet collector
16. A socket of connection of the oxygen gauge
17. A socket of connection of a heating element of the oxygen gauge
18. A vacuum hose
19. The oxygen gauge
20. An alarm bulb

Elements of the bottom section of an inlet collector on engine AAR, AAN

1. A hose from the fuel distributor
2. A connection bolt банджо
3. A connection socket
4. The valve of system of cold start
5. A lining
6. A tube going to the distributor of fuel
7. A connection nut
8. An injector
9. Sealing rings
10. A lock ring
11. An insert
12. The bottom section of an inlet collector
13. An air hose
14. The holder of injectors
15. The valve of system of stabilisation of idling
16. A fixing arm
17. The gauge of temperature of a cooling liquid
18. Consolidation
19. A final knee

Elements air заслонки on an inlet collector (engine ADR)

Removal

PERFORMANCE ORDER

1. Remove the case throttle заслонки.

2. On engine ADR (Motronic 3.2) remove a fuel collector and disconnect a water tube () and a hose from a broad tank (), located over an inlet collector.

3. Disconnect vacuum and air hoses from an inlet collector. Disconnect connection sockets.

4. Remove fastening of a rope of an accelerator from the top section of an inlet collector and disconnect hoses and wires from air заслонки if it is necessary (See fig. Elements of the top section of an inlet collector engine AAR, AAN and Elements air заслонки on an inlet collector (engine ADR)).

5. On engine AAR (KEIII Jetronic) remove the top section of an inlet collector.

6. Gradually turn off fixing bolts and remove an inlet collector or its bottom section (Elements of the bottom section of an inlet collector fig. See engine AAR, AAN).

Installation

Installation is spent upside-down removals.

On the main page