Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

5.2.1.3. Components of system of injection for 5-cylinder models

THE GENERAL DATA

Components of system of injection for 5-cylinder models

1. Return топливопровод (to the fuel tank) 2. 20 Н.м. 3. A regulator of pressure of fuel 4. An arm 5. 20 Н.м. 6. 10 Н.м. 7. A ventilating hose (to the top part of the air filter) 8. A bolt (antimagnetic) 9. A pressure difference regulator About 17,5–21,5 Ohm 10. The electroplug 11. The lock screw of operating плунжера 12. The electroplug 13. Ventilation картера the engine 14. For idling stabilisation 15. A cover of soaked up air 16. The electromagnetic valve of the coal filter 17. To the coal filter 18. Ring consolidation

19. A sealing ring Smaller diameter is directed to the managing director плунжеру 20. Operating плунжер 21. The fuel distributor After installation of the fuel filter, check up a free wheeling of a plate of the gauge of an air stream 22. 20 Н.м. At replacement establish a bolt "банджо* instead of the minifilter 23. 10 Н.м. 24. Шестигранная заглушка 25. To the valve of start from a cold condition 26. 10 Н.м. 27. Submitting топливопровод (from the fuel filter) 28. To инжекторному to the valve 29. 3.5 Н.м. 30. 20 Н.м. 31. 3.5 Н.м.

Components of system of injection for 5-cylinder models

1. Заглушка Remove before adjustment of deduction WITH 2. An electrosocket 3. A potentiometer 4. Ring consolidation 5. A hose (to a final cranked branch pipe) 6. The channel приточного air The channel приточного air has the managing director заслонку and the thermostat The managing director заслонка closes, above +10 ° With: inflow of warm air More low 0 ° With: inflow of cold air

7. A connecting hose 8. A casing of the air filter нижняячасть 9. 20 Н.м. 10. A filtering element of the air filter 11. A casing of the air filter The top part 12. A lining 13. A casing of the gauge of an air stream 14. The mesh filter Installation position: curvature to a cover

Components of system of injection for 5-cylinder models

1. The electroplug 2. An arm 3. The mode switch completely open throttle заслонки 4. Fastening of a rope of management throttle заслонкой 5. To запорному клвпану the coal filter 6. The switch of a mode of idling 7. A clip 8. 20 Н.м. 9. A lining 10. An inlet collector The top part 11. To the amplifier of brake system 12. The electroplug for the oxygen gauge 13. The oxygen gauge 50 Н.м. Cover a carving with structure G5 In каталитическое the converter 14. The electroplug for the oxygen gauge Heating element

15. 10 Н.м. 16. An arm 17. A thermoswitch For postoperative work of the delivery fan, for cooling of fuel injectors 18. An arm of fastening of a rope of gas 19. A lining 20. The block of management of fuel injection For сиситемы injection, management of the oxygen gauge and idling stabilisation 21. The electroplug of the block of management Disconnect or connect the electroplug only at the switched off ignition For removal unhook a spring clamp on the management block

Components of system of injection for 5-cylinder models

1. 10 Н.м. 2. To the fuel distributor 3. The valve of start from a cold condition 4. 10 Н.м. 5. A clamp 6. To the fuel distributor 7. 20 Н.м. 8. Топливны an injector 9. Ring consolidation Cover with greasing before installation 10. Всавка for a fuel injector 11. The rubber block of fastening 12. Электрдразъем 13. 10 Н.м. 14. An arm

15. The operating valve for idling stabilisation 16. An insert for a fuel injector 17. Rings 18. The combined temperature gauge 19. A system flange 20. A sealing ring 21. The electroplug 22. A lining 23. 10 Н.м. 24. To a cover of soaked up air 25. An arm for fuel injectors 26. An inlet collector The bottom part 27. A lining 28. An electrosocket