Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A plug - the main cylinder of coupling
   8.1.3. Press a coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. A mechanical transmission 012
   + 8.3. A mechanical transmission 01А
   + 8.4. An automatic transmission 089
   - 8.5. An automatic transmission 087
      8.5.2. The lever and a rope of the lever of a gear change
      8.5.3. The mechanism of management throttle заслонкой
      8.5.4. Removal and transmission installation
      8.5.5. Check of the moments of a gear change
      8.5.6. The main transfer
   8.6. Dismantling and assemblage of automatic transmissions
   8.7. The block of valves
   + 8.8. An automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment

8.5.4. Removal and transmission installation

Removal

PERFORMANCE ORDER
1) disconnect a wire of the negative plug of the accumulator
2) remove the top bolts of fastening of the engine and a transmission
3) disconnect a wire of grounding of a transmission
4) disconnect a socket of connection of a speedometer and the oxygen gauge
5) establish a support under the engine
6) press cooling hoses between the engine and a transmission
7) lift the car
8) remove a protective plate of the engine and fastening
9) remove bolts of forward fastening of the engine
10) remove a forward exhaust pipe
11) remove a starter
12) remove 3 bolts of fastening of the hydrotransformer (4 bolts on cars with a turbo-supercharging)
13) remove a hydrotransformer filter

14) remove clips from hoses of a radiator of a cooling liquid of an automatic transmission

15) remove a hose of a cooling liquid from a tube
16) remove a filter of fastening of a transmission and карданного a shaft
17) disconnect semiaxes from the main transfer and tie up to the body bottom
18) remove an arm of a rope of a gear change and disconnect a rope from a transmission
19) on cars with system of a tension of seat belts, remove directing a rope
20) disconnect draught of an accelerator
21) disconnect a rope of an accelerator and remove it from transmission fastening
22) remove both fastenings of a transmission from a car body
23) disconnect a rope of an accelerator from the lever of switching of a transmission
24) lift a transmission by means of the lift and remove the right and left fastenings of a transmission
25) lower the lift and lift the engine, having lifted an engine support (a transmission thus slightly to bend for simplification of removal)
26) remove remaining bolts of fastening of a transmission and the engine
27) ослабьте fastening of a jellied tube of a liquid of cooling of an automatic transmission
28) disconnect a transmission from the engine
29) move right полуось forward
30) accurately lower the engine, thus support the hydrotransformer that it has not fallen

Installation

Installation is spent upside-down removals, thus pay attention to the following:

PERFORMANCE ORDER
1) establish the hydrotransformer before transmission installation
2) accurately establish the hydrotransformer on fastening unilateral муфты
3) do not incline the hydrotransformer and watch accuracy of its installation
4) at hydrotransformer installation, turn it forward-back to establish шлицевой a pump shaft
5) establish a transmission
6) check up adjustment of a rope of an accelerator
7) check up adjustment of a rope of the lever of a gear change

The inhaling moment

Semiaxis fastening to a drive flange 45 Н.м.
Bolts of fastening of the hydrotransformer 30 Н.м.
Bolts of fastening of a transmission to the engine 35 Н.м.


On the main page