Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

8.8.2. The lever and a rope of the lever of a gear change

THE GENERAL DATA

The lever перключения transfers / a gear change Rope

1. A cover 2. The program switch (Е122) 3. A casing of the lever of a gear change усанавливайте a designation of the parking Transfers forward Establish after adjustment The electromagnetic switch 4. The handle of the lever of a gear change 5. 9 Н.м. 6. A washer 7. The solenoid of the lock of a gear change (№ 110) 8. 10 Н.м. 9. A torsionnaja spring 10. The gear change lever With a plug for lever short circuit in position Р and N 11. The plug торсионой springs 12. A directing pin Establish after installation компрессионной springs 13. A kompressionnaja spring Establish on the gear change lever Before installation of a directing pin 14. A lock ring 15. A washer 16. The basis Put a layer of hermetic AKD 512 001 05 between the basis and a body Establish bolts and fastening washers (the moment Inhalings 10 Н.м.) 17. The plug 18. A washer 19. The switching lever 20. Муфта 21. A nut The moment of an inhaling 20 Н.м. 22. A washer 23. The plug 24. Муфта 25. A washer 26. A cartridge 27. A cover Replace if it is necessary Check up accuracy of installation, that a moisture not Has got on a rope of the lever of a gear change 28. 23 Н.м. 29. A clip

30. Transmission fastening With fastening of a rope of a gear change 31. 40 Н.м. 32. A gear change rope With the directing plug Grease the rope ends before installation Do not bend and do not overwind a rope For adjustment: преключите the gear change lever in position Р ослабьте a nut on a rope clip предвиньте the lever on a transmission in position Р (against the stop back) After that, when the rope is in a loose condition, tighten a nut (21) to 20 Н.м. After rope adjustment check up work of the switch of the lever преключения transfers and adjust it if it is necessary 33. An arm of a rope of the lever of a gear change 34. The clip screw 35. A clip 36. 5 Н.м. 37. The switch of the lever of a gear change Check: The engine should be started only when the gear change lever is in position Р or N Backing headlights should join at inclusion of transfer of a backing If is not present, turn the switch in a nest and again провверьте its work 38. The plug

Installation of an arm of the lever of a gear change in relation to the gear change lever

PERFORMANCE ORDER

1) translate the gear change lever in position R And – probe for measurement of backlashes by thickness of 1.0 mm 2) establish probe between the lever of a gear change and the electromagnetic switch 3) press the electromagnetic switch to probeу and tighten a fastening nut 4) establish on the centre the bottom aperture of a plug of the lever of a gear change and submit pressure on the switch 5) the solenoid pin will close a plug 6) establish a casing of the lever of a gear change so that the gear change lever was opposite to mark N in a casing 7) the gear change lever should pass identical distance between positions N and D and positions N and R 8) establish the lever And by means of a pin or a drill In (diameter 4.0 mm), inserted into a casing aperture

The switch of the lever of a gear change, installation

PERFORMANCE ORDER

1) switch the gear change lever in position in position N 2) establish the switch so that fastening (it is specified by an arrow) was fixed on the gear change lever 3) tighten bolts of fastening to 5 Н.м. 4) remove a pin or a drill

After switch installation, check up its work.