Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
- The operation manual
   The car equipment, arrangement of devices and controls
   Operation receptions
   Comfort
   Recommendations about car operation
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Comfort

Ventilation

Air circulation

The climatic comfort is reached at the expense of uniformity of distribution of air streams on salon volume.


The scheme of distribution of air streams

Nothing should disturb to free receipt of air. Watch lattices of the air inlet located in the basis of a windscreen, regularly clear it of dry leaves and other extraneous subjects, delete snow stoppers in the winter. Try to avoid water hit in air inlets at car washing.

Do not block pass under forward seats to provide air unimpeded access in foot wells of a back part of salon.

Дефлекторы lobbies snuffled ventilating air lines are supplied рычажками, allowing to regulate receipt intensity of giving of air and a direction of its stream (upwards-downwards, to the right-to the left).

Management of functioning of systems of heating/ventilation of salon

Control lever distribution of an air stream

The choice of a direction of distribution of an air stream on car salon is carried out by means of the lever (1) on the control panel by functioning of systems of heating/ventilation. The control panel is located in an average part of the panel of devices directly over a place of its joint with the central console (the Scheme of distribution of air streams see an illustration).


The control panel functioning of systems of heating/ventilation of salon

1 — the Control lever distribution of an air stream
2 — the Lever of a choice of the scheme of air circulation

3 — the Control lever in temperature of air submitted to salon
4 — the Lever of a choice of a high-speed mode of the fan

While translating a control lever by air distribution in the given vent position of an air stream it is carried out at level of the person.
Lever transfer in the given position the air stream goes to foot wells.
In the given position the stream in regular intervals is distributed between nozzles of foot wells and blowing a windscreen.
The given position of the lever should get out for intensive blowing a windscreen.

The lever of a choice of the scheme of air circulation

By means of the lever (2) on the control panel the choice of one of two possible schemes of air circulation is carried out: opened or closed (the Control panel functioning of systems of heating/ventilation of salon see an illustration).

When the lever is translated in extreme right position, the open scheme of circulation when in salon fresh external air constantly continues to arrive is carried out. The given scheme is the most productive at struggle with отпотеванием glasses.

Lever transfer in extreme left position carries out system switching in a mode closed recycling air in salon. The given scheme is used at journey through strongly dusty or загазованные areas, and also, to prevent hit in salon of badly smelling air. Remember that long use of a mode closed recycling leads to developments of stagnation, and also is fraught отпотеванием glasses.

Regulator of temperature of air

By means of the lever (3) (the Control panel functioning of systems of heating/ventilation of salon see an illustration) administration in temperature of air forced in salon is exercised.

The lever (4) (see in the same place) serves for inclusion/deenergizing of the fan and a choice of a high-speed mode of its functioning.

Models with air conditioner

Air central air enters into a complete set of some models (К/В), allowing to support the most comfortable environmental conditions in car salon without dependence from temperature and humidity of air. In a refrigerator path of system the non-polluting coolant is used. The system of cooling of air operates only at the working engine.

For inclusion К/В press the switch located on the panel of devices, near to the alarm system switch. The switch button is equipped by the green control lamp confirming activation of system.

Remember that peak efficiency of functioning of the conditioner can be reached only at the closed windows.

At an excessive warming up of salon during long parking on the open sun before to include the conditioner air salon by opening of windows (do not forget then them to close).

For increase of efficiency of functioning of a central air and speed of cooling of salon in hot weather use a mode closed recycling air for what move a control lever () to extreme left position.


The control panel functioning of systems of heating/ventilation and an air conditioning

The lever of a choice of a high-speed mode of the fan () establish in average position. In order to avoid a stagnation of closed air, cancel a mode recycling at once as soon as the salon will enough be cooled.

In order to avoid destruction of a material of sealing cuffs of components охладительного a path the conditioner should be used regularly, joining for short time at least once a month.

Use К/В in a winter season allows to cope as fast as possible отпотеванием glasses in salon.

At switched off К/В the temperature of air salon cannot be supported below an ambient temperature.

The choice of temperature of air submitted to salon is carried out by means of the lever () (functioning of systems of heating/ventilation and an air conditioning) the Control panel see the control panel (in a combination to inclusion/deenergizing К/В an illustration). To optimum environmental conditions there corresponds position of the lever 22. At will of the operator air can be warmed in addition up, or is cooled.

In extreme positions of the lever (dark blue and red sites of a scale) the automatic mode of adjustment of speed of rotation of the fan (see more low) does not operate.

The choice of a high-speed mode of functioning of the fan is carried out by means of the lever () (see in the same place). Position AUTO corresponds to a choice of a mode of automatic adjustment of speed of forcing of an air stream. Besides an automatic mode the choice of a high-speed mode can be carried out by moving of the lever at the discretion of the operator in one of five discrete positions (on increasing from left to right).

Marked with the image крыльчатки lever position corresponds to fan switching-off.

Struggle with отпотеванием glasses

While translating a control lever distribution of an air stream (D) (the Control panel functioning of systems of heating/ventilation and an air conditioning see an illustration) in the position corresponding обдуву of glass, the system of automatic adjustment carries out selection of optimum temperature and high-speed modes blowing wind and forward lateral glasses, depending on temperature of external air.

For maintenance of the most comfortable conditions in salon translate lever D in the position second on the right.

The choice of a temperature mode is carried out by means of V.Krajnee's lever the left position of the lever answers the minimum temperature of submitted air, extreme on the right - maximum.

Composers of the present Management offer the following base scheme of adjustment of environmental conditions in car salon:

Temperature of external air

Choice of a direction of giving of an air stream

Position дефлекеторов ventilating glasses

The low

In feet or in feet and on having blown in glasses

Lateral are opened, central are closed

Average

In feet

All four are closed

The high

In the person

All four are closed

Salon illumination

The forward ceiling fixture

In a plafond of the ceiling fixture it is built in having two position ползунковый the switch. Transfer of a toddler of the switch in the left position carries out inclusion of a constant mode of illumination. In the right position of a toddler the fixture will join only at opening of any of car doors. Switching-off of the fixture after closing of doors occurs to a delay in 15 seconds.

The back ceiling fixture (models the Versatile person)

Built in in a plafond of the back ceiling fixture (models the Versatile person) the switch has three positions: while translating a toddler (1) fixture will join in position at opening of a door of a back; on the average position (2) fixture is disconnected; position (3) allows to include the fixture in a mode of constant functioning.

Lamps for reading

Inclusion and deenergizing of a lamp for reading is carried out by means of the individual switch built in in its plafond. Lamps operate only at the included ignition.

Luggage space illumination

Illumination joins automatically at opening of a door of a back.

Illumination of a ware box

Illumination joins automatically at opening of a cover of a box and functions only at the included ignition. Do not forget to close a box.

Ware boxes

Door pockets

For pocket opening raise and delay an armrest.

The main ware box of the panel of devices

The main ware box is located from the passenger party of the panel of devices and on models without safety pillows. It consists of two sections (top and bottom).

On an illustration illumination of a foot well also is shown.

On the models equipped with a passenger pillow of safety, the top section of a box is occupied by the pillow module.

In a cover (ah) a ware box deepening under the handle is provided.

Illumination of a foot well

The illumination lamp is located under the panel of devices and joins at opening of a corresponding door of the car, shining a rug in a foot well and space under the panel of devices (see an illustration above)

Pocket for storage of the coupon of passage of checkup

The pocket is fixed on a windscreen from outside the driver.

Electronic clock

Assemblage of hours is built in in an average part of the panel of devices, to the right of the button of inclusion of the alarm system.

At inclusion ignition on the display of hours for 5 seconds date is highlighted, then hours come back in a mode of display of current time.

For compulsory выcandlesивания dates press button D to the right of the display of hours (see an illustration above). Hours will return To a mode of display of time automatically later 10 seconds, or by repeated нажимания on button D.

Display and time installation are made only at the included ignition:

By means of button N (see an illustration above) updating of the hour indicator is made.

The M button carries out updating of minutes. Transfer from the 12-sentry of a cycle on the 24-sentry also is back carried out by simultaneous нажимания on both buttons N and M.

Date installation is made also at the included ignition. Button N makes updating of indications of the left zone of the screen, by the M button - right. Transfer from a mode day/month in a mode month day also is back made simultaneous by squeezing of both buttons N and M.

Temperature measuring instrument

At the included ignition the measuring instrument screen highlights temperature of external air. If air temperature is in limits between + 3С and - 3С, on the display screen the snowflake image starts to blink. At temperature more low - 3С the snowflake starts to be highlighted constantly.

The shown temperature can be above, than real if the car costs on the sun.

Ashtrays/prikurivatel

Assemblage of a forward ashtray with прикуривателем

Assemblage of a forward ashtray with прикуривателем is established in an average part of the panel of devices under the control panel functioning of systems of heating/ventilation / of an air conditioning.


 PERFORMANCE ORDER

1. Drown the button прикуривателя and wait for some seconds. When the working element of a heater will be heated, the button will automatically jump out of the nest. Be cautious, lighter functions and at the included ignition!

2. For ashtray extraction, pull for the uvula located under it and raise assemblage on itself. Installation is made upside-down (fill assemblage in a nest and push downwards).

Back ashtray of the central console

For ashtray opening push/pull an assemblage cover back in a direction of a back seat. To liberate an ashtray, pull it on itself, pressing a uvula.

The poruchnevaja handle with a hook for clothes

Handles are located along the edges of the ceiling panel over doorways.

Sun-protection peaks

Collapsible peaks are located directly over a windscreen and serve for protection of eyes of the driver and the forward passenger against hit of direct solar beams. Possibility of deployment of peaks for protection against lateral beams is provided also: liberate from a support an internal arm of assemblage and develop a peak towards lateral glass.

On some models the sun-protection peak can be equipped by a toilet pocket mirror with illumination which joins automatically at opening of a cover of a pocket mirror.

Back sun-protection шторка (models of Hetchbek)

Шторка fastens over back glass of the car. For its deployment pull for a special uvula and fix its cores. Deployment шторки does not disturb to opening of a door of a back.

Branch for storage of documents

On an inside of a cover of the assembly block of safety locks the special branch for storage of driver's documents is provided. The assembly block is located at the left under the panel of devices of the car, for opening of its cover turn the handle on a turn quarter.

Adjustment of height of a road gleam

Possibility of adjustment of height of a road gleam allows easily and to adapt the car for any road conditions quickly. Except for rare occurences it is offered to use normal height of installation of a suspension bracket. For updating of height of a suspension bracket unblock, having pulled upwards, the handle of management located on the central console of the car and move it to corresponding position.

The handle of updating of height of a road gleam

The minimum height of installation of a suspension bracket should be used only at checkup passage.

Normal position serves for car operation in usual road conditions.

Suspension bracket transfer in intermediate position allows to adapt the car for cross-country conditions. Rigidity of a suspension bracket essentially increases in this position, it is necessary to move on the minimum speed.

The maximum position at car movement should not to be used and serves for performance of replacement of wheels and the control of level of a hydraulic liquid.

Performing any works under the car, do not forget to fix a body props!

Hydroactive suspension bracket

The height of position of a hydroactive suspension bracket is supervised by an electronic control system. It is provided two modes of functioning of a hydroactive suspension bracket switching between which is carried out by the special button of management located on the panel of devices of the car, to the left of buttons of the alarm system and темпостата. In the button the control lamp of yellow colour is built in.

At the wrung out button (the control lamp does not burn) the mode of usual movement providing the maximum degree of comfort with tracing of changes of road conditions joins.

At утапливании buttons (the control lamp burns) transition to a sports mode of movement, more actual is made at moving on twisting roads.

The suspension bracket design provides also possibility of the control of a list of a body of the car, allowing in an essential measure to raise comfortableness of movement safety at fulfilment of abrupt turns. Be careful at driving, not лихачьте!

Variants of connection of a radio tape recorder

Open a niche cover under installation of a radio tape recorder and take a casing, having provided with that access to колодкам three contact sockets of electroconducting and to the tip of an antenna cable.

Study the instruction of the user of a radio tape recorder.

Колодки contact sockets of electroconducting of a radio tape recorder

In standard assemblages following schemes of an arrangement of contact plugs in колодках electric sockets are used:

А1

-

B1

(+) Right back динамик (if it is provided)

А2

-

B2

(-) Right back динамик (if it is provided)

А3

-

B3

(+) Right forward динамик

А4

(+) Constantly energised

B4

(-) Right forward динамик

А5

-

B5

(+) Left forward динамик

А6

(+) The Rheostat

B6

(-) Left forward динамик

А7

(+) Accessories or (or it is constant energised)

B7

(+) Left back динамик (if it is provided)

А8

Weight

B8

(-) Left back динамик (if it is provided)

 

WITH

Socket of a supply of electroconducting of remote control from a steering wheel

It is necessary to remember that for optimum reception of a radio signal the aerial mast should be inclined. We recommend to incline the aerial in parallel a windscreen.

Installation of loudspeakers

Loudspeakers on the panel of devices

Along the edges of the panel приоров two loudspeakers are located. Remove decorative lattices, connect dynamics, fix their two screws and return to the place of a lattice.

Loudspeakers of forward and back doors

On forward doors of 165 mm are established dynamics in diameter.

 PERFORMANCE ORDER

1. Having hooked a thin screw-driver, release three clamps and remove a decorative lattice.

2. According to marks cut out the bottom part of the isolating panel, having prepared thereby a nest under installation dynamics.

3. Connect динамик and fix it by means of four nuts. Establish into place a lattice.

On back doors of 130 mm are put dynamics in diameter. The installation order is similar described above for loudspeakers of forward doors.

The top hatch

The top hatch does not enter into a standard complete set of all models.

The hatch can or rise from back edge, or move together with sun-protection шторкой.

Sun-protection шторку it is possible to push manually both at the closed hatch, and after a raising of its back edge.

The switch of management is located by functioning of the electric drive of the top hatch on the central console, behind the handle of updating of a road gleam.


Installation of the top hatch as an additional complete set on the models equipped with lateral pillows of safety, is forbidden!


On the main page