Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation

1.28. The AM-UKV-RADIO TAPE RECORDER with electronic adjustment

THE GENERAL DATA

Using the receiver

PERFORMANCE ORDER

1. Include the receiver, having pressed button L.M.U., choose a mode of a stereo- or monophonic reception, or press button TI for reception of station of an announcement of the road information (see more low). On the display there will be symbols L, M, or U. The receiver can be included also pressing handle "PWR.VOL". 2. Adjust loudness, turning handle "PWR.VOL". 3. Be adjusted on the necessary station (Adjustment for station and adjustment Programming see). 4. At adjustment for VHF-station the receiver will automatically be switched in a stereo-reception mode. On the display there will be symbol ST. 5. If a signal weak there will be an automatic narrowing of a strip of reception for the purpose of decrease in noise. 6. If a signal very weak there will be an automatic switching of the receiver on a monophonic mode of reception. 7. Adjust a timbre and balance (Adjustment of a timbre and balance Adjustment see). 8. To switch off the receiver, press handle "PWR.VOL".

Adjustment for station

PERFORMANCE ORDER

1. Be adjusted on the necessary station by means of one of offered below ways. On the display there will be a value of frequency of adjustment. Adjustment in a program mode 2. It is used for adjustment for in advance programmed station (adjustment Programming see). 3. Press some times button LMU until then while on the display there will be no chosen information. 4. Press the button with number which has been in advance appropriated the necessary station. There is an adjustment for the necessary station, and on the display there will be number of the button of the necessary station. Mode of continuous search 5. In this mode there is an automatic search of station. After reception of station adjustment automatically stops. 6. Press simultaneously on both parties of button TUNE SEEK and wait a continuous sound signal. The receiver will start to carry out automatically search of the nearest station with higher or lower frequency of an announcement. 7. After confident reception adjustment stops. By each subsequent pressing of the button search will proceed before confident reception of the following station. 8. If because of too weak signal it is not possible to be adjusted after unitary scanning in all range of frequencies search will proceed, but at a hypersensibility, and on the display there will be symbol DX. Manual adjustment 9. Press simultaneously on both parties of button TUNE SEEK for a while not exceeding 0,5 seconds By each pressing of the button occurs перескок to frequency on which the announcement is possible.

Adjustment programming

PERFORMANCE ORDER

1. Press some times button LMU, until then while on the display there will be no designation of chosen range L, M or U. 2. You can establish to six stations in each chosen range (on each pressed button). At station installation check up those ranges in which the necessary adjustment already is. 3. Be adjusted on the necessary station (Adjustment for station see). 4. Press one of buttons of a choice of station and wait a sound signal. Thus the station will automatically join by pressing the given button, which number will appear on the display. 5. To bring in memory adjustment for new station repeat the procedure described above. 6. Adjustment for the programmed station is erased at food switching-off (a battery detachment, перегорании a safety lock etc.).

Reception of the road information from system RDS (radio data)

PERFORMANCE ORDER

1. The receiver will automatically be switched in a mode of reception of the station broadcasting the RDS-information at switching on VHF-range. At switching on the display there will be a name of corresponding radio station and symbol RDS. 2. If to be adjusted on new VHF-station, broadcasting RDS - the information on the display there will be a value of frequency, and through 5 сек there will be a name of corresponding radio station. 3. Adjustment for the necessary station which broadcasts the road information, is carried out by one of next ways. Adjustment by programming, automatic search and manually 4. The adjustment order is described above. Adjustment by scanning in all range 5. When on the display there is symbol ТР (Traffic Program) it means that the given station will broadcast the road information and data EON. 6. The receiver is switched to range TI by button "TI" pressing. Thus on the display there will be a symbol "TI". 7. If later 20 сек after pressing of button "TI" the receiver does not find out station search of station on the basis of the list of alternative frequencies (list AF) which comes to an end at station detection will begin. 8. About transition of the receiver to such mode warns a sound signal and symbol SEARCH on the display. 9. If to be adjusted on station after unitary scanning in all range it will not be possible because of a weak signal scanning will repeat, but at a hypersensibility to what symbol DX on the display will testify. 10. If the signal too weak the receiver will stop search and on the display for 2 seconds appears NOTHING. 11. If within even 20 seconds the receiver is not adjusted on TI-range station scanning will begin at first. 12. When on the display will appear TI, the receiver will accept station TI only in that case if adjustment is made by search in an automatic mode. 13. If reception of the road information, and station on which the receiver is adjusted is required, broadcasts other program press button TI and keep until then while on the display there will be no symbol THAT (Traffic Announcement). 14. At occurrence of this symbol the receiver ceases to accept all programs except road or if transfer of the road information at present is absent, and the cartridge the player which is automatically switched off at the moment of the beginning of an announcement of the road information joins is inserted into a player. 15. After the termination of transfer or if the signal becomes weak, the previous program joins. 16. To come back from a mode of reception of the road information to a usual mode press button TI and keep until then while from the display the symbol THAT will not disappear. Adjustment for a tracking mode on networks (NF-mode). It is used for RDS-station search in all strip of frequencies 17. Press button NF and keep no more than 2 сек, thus the receiver will be adjusted on RDS-station, and the accepted program will not interrupt. On the display there will be symbol NF. 18. At deterioration of conditions of reception adjustment for station which broadcasts the same program, will be made on the basis of the list of the alternative frequencies received from RDS-station.

Timbre adjustment

PERFORMANCE ORDER

1. For reproduction adjustment in to acquire the bottom frequencies press some times button MODE, until then while on the display will not appear BASS O. 2. Then press the button of level from any party and establish the necessary timbre. The adjustment range – from BASS-10 to BASS +10, timbre level is displayed on the display. 3. For reproduction adjustment in to acquire the top frequencies press some times button MODE, until then while on the display will not appear TREB O. 4. Then press the button of level from any party and establish the necessary timbre. The adjustment range – from TREB-10 to TREB +10, timbre level is displayed on the display.

Balance adjustment

PERFORMANCE ORDER

Two dynamics 1. Press some times button MODE, until then while on the display will not appear BAL O. 2. Then press the button of level from any party and establish the necessary balance. 3. The range of adjustment of balance for left and right dinamikov - from BAL L14 to BAL R14, balance level is displayed on the display. Four dynamics 4. For balance adjustment between left and right динамиком press some times button MODE, until then while on the display will not appear BAL O. 5. Then press the button of level from any party and establish the necessary balance. 6. The range of adjustment of balance – from BAL L14 to BAL +R14, balance level is displayed on the display. 7. For balance adjustment between forward and back динамиками press some times button MODE, until then while on the display will not appear FADE O. 8. Then press the button of level from any party and establish the necessary balance. 9. The range of adjustment of balance forward and back динамиков – from FADE F14 to FADE R14, balance level is displayed on the display.