Audi 100

1982-1990 of release

Repair and car operation

Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
- 7. Transmission
   + 7.1. Coupling
   + 7.2. A mechanical drive of deenergizing of coupling
   + 7.3. A hydraulic drive
   - 7.4. A transmission
      - 7.4.1. Type 014 four-speed transmission Removal and dismantling Dismantling and assemblage of a primary shaft Dismantling and assemblage of a secondary shaft Assemblage and synchronizer dismantling Dismantling and differential assemblage Transmission assemblage Selection of a thickness of adjusting rings of back bearings The gear change lever Adjustment and installation of the mechanism of management by a gear change
      + 7.4.2. A five-speed transmission of type 013 or 093
      + 7.4.3. A five-speed transmission of types 016 and 012
      + 7.4.4. The mechanism of management of gear change КП of type 016
      + 7.4.5. An automatic transmission
   + 7.5. A drive of forward wheels
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment Dismantling and differential assemblage


1 – a bolt;
2 – a spring washer;
3 – a differential box;
4 – a separator;
5 – a semiaxial gear wheel;
6 – a satellite gear wheel;
7 – a nut;
8 – an axis;
9 – a conducted gear wheel;
10 – a stopper

Installation of a leading gear wheel of a drive of a speedometer

1 – the plug;

2 – a leading gear wheel of a drive

3 – a bolt;

4 – a flange of a box of differential;

5 – a conducted gear wheel of the main transfer;

6 – a differential box;

Хвыступание plugs


1. To press a leading gear wheel 2 (fig. Installation of a leading gear wheel of a drive of a speedometer see) drive of a speedometer from a differential box.
2. To press differential bearings. It is recommended to mark them concerning what party they stood.
3. To mark a relative positioning of a conducted gear wheel and a flange of a box of differential. To turn away eight bolts 1 (fig. Differential) fastenings see and to press a conducted gear wheel 9 main transfers from a box of 3 differentials.
4. A thin firm core to beat out from an aperture of a box of differential a stopper of 10 axes of satellites. To beat out from a box an axis of satellites.
5. To take out перекатыванием satellites, and then to take out semiaxial gear wheels with round nuts.
6. To take out a separator 4.


1. To establish in a box of differential 3 separator 4.
2. To establish semiaxial gear wheels 5 with круглами nuts 7.
3. To insert into windows of a box satellites, having entered them into gearing with semiaxial gear wheels. To insert temporarily both flanges of a semiaxis and to turn them so that apertures under an axis on a box of differential and satellites were combined.
4. To insert an axis of 8 satellites, having combined apertures in a box and an axis under a stopper. To fix an axis of satellites a stopper 10.
5. To heat up a conducted gear wheel to temperature 100 With and напрессовать it on a box of differential 3. For this purpose it is possible to take advantage of two bolts of 1 its fastening.
6. To allow to a gear wheel to cool down and wrap all bolts of 1 its fastening by the moment 55 Нм (5,5 кгсм).
7. To heat up internal rings of bearings of differential to temperature 100 With and напрессовать them on a differential box.
8. To establish a leading gear wheel 2 (fig. Installation of a leading gear wheel of a drive of a speedometer) a drive of a speedometer see and напрессовать the plug of 1 drive, having provided it выступание on 1,4 mm with selection of adjusting rings by thickness from 1,4 to 1,5 mm.

On the main page