Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
Forward bumpers
Forward part of the car
Cowl
Wings
Молдинги
Doors
External rear-view mirrors
The forward and back has flown down
Cover of a luggage carrier at a sedan
Back door of the versatile person
Back bumper
The sdvizhnoj hatch
Procleaning of apertures for a water drain
The control of anticorrosive protection of the bottom of a body
Salon
Seats
+ Search of malfunctions
+ Specifications
|
Back door of the versatile person
Drive of the lock of a back door of the version the versatile person
|
|
For regulation of a back door from within the car it is necessary to insert between the lock and a lock plate распорную a plate in the thickness of 3 mm (in drawing it is allocated by red colour). |
Removal
|
|
- To remove a covering of a back door.
- To disconnect or remove electric plug connections, a hose of system of locks with the central management and a hose to a back atomizer стеклоомывателя.
- To open a back door and to prop up it.
- To wring out pneumatic springs from the top spherical pins (on a door).
- To turn off шестигранные bolts above on a door loop. Two assistants should hold a door at the left and on the right.
- At installation to replace sealing washers between a loop and a door of a luggage compartment.
- To adjust the adjusting buffer of a back cover so that at the closed door between the buffer and a body there was a distance of 2-4 mm.
|
|
Removal of the cylinder of the lock
Removal of the cylinder of the lock occurs identically with described in section «Removal of the lock of a luggage compartment» for a sedan.
Removal of a drive of the handle of a back door
The versatile person
|
|
- To remove a covering of a back door.
- To disconnect all connecting draughts from a handle drive.
- For this purpose to take aside lock скобы connecting bent for to locks.
- To turn out two шестигранных a bolt with nuts.
- To take out a handle drive.
- Installation: in the middle and in parallel to enter a drive of the handle from a luggage compartment through a rectangular aperture in the bottom external part of a door.
- The stopper and sealing lining with a groove should adjoin to the bottom external part of a door.
- To turn a handle drive until apertures through passage and fixing apertures in the bottom part of a door will coincide.
- To tighten a drive of the handle a washer and шестигранным a bolt (10 Н•м).
- Again to hang all connecting draughts and to adjust their length.
- Connecting bent for to the lock cylinder: to establish the deenergizing lever in position is opened".
- To remove back сдвижную the button in the middle of connecting draught so halves are freely inserted each other.
- In this position to fix one in other carving parts of halves of draught and to stop сдвижной the button.
- To adjust connecting bent for to locks of a back door – look the following section.
|
|
Removal of locks of a back door
The versatile person
|
|
- To remove an internal covering of a back door.
- To uncouple connecting draughts of locks, having taken aside lock скобы.
- In each lock to turn on two шестигранные nuts in a door frame.
- To take out the lock in a direction inside.
- Installation: slightly to tighten nuts of locks, to establish fastening points on the centre.
- A few to weaken locking скобу (a lock part below on a body).
- To close a back door.
- From within a luggage compartment to enclose распорную a plate (thickness of 3 mm) between the lock and locking скобой.
- To close the lock in the second lock groove and to expose a back door.
- To adjust and fix backlashes. The backlash between an upper edge of a bumper and a bottom edge of a back door should make 6,5—7,5 mm.
- To tighten шестигранные nuts.
- To remove распорную a plate; regulation of the lock of a back door is finished.
- Now it is necessary to establish length (built in) draught of a drive: to remove back сдвижную the button in the middle of both connecting draughts so that halves have been freely inserted one into another.
- Lock latch at an open back door to put in position "is closed" (the second lock groove).
- In this position to fix carving parts of halves of draught one in another and to stop сдвижной the button.
|
|
|
On the main page
|