Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
Forward bumpers
Forward part of the car
Cowl
Wings
Молдинги
Doors
External rear-view mirrors
The forward and back has flown down
Cover of a luggage carrier at a sedan
Back door of the versatile person
Back bumper
The sdvizhnoj hatch
Procleaning of apertures for a water drain
The control of anticorrosive protection of the bottom of a body
Salon
Seats
+ Search of malfunctions
+ Specifications
|
Молдинги
Removal of lobbies молдингов
|
|
- Молдинг on a forward wing: to remove facing of a wheel niche.
- From the interior of a wing to turn on шестигранную a nut.
- To shift молдинг back and to remove from a wing.
- Молдинг on a lateral part behind (a back wing): to warm up молдинг the hair dryer to temperature approximately 40°С.
- Then to take out молдинг from a fixing percussion cap the screw-driver which has been wrapped up in a rag.
- At installation to insert молдинг in fixing клипсу and in addition to paste (for example as it is described more low or in the help).
- Молдинги on doors: to disconnect an overlay from a glutinous layer.
- In most cases it can be made, only heating молдинг the hair dryer approximately to temperature 40°С, but also in this case more often the overlay does not manage to be removed the intact. Therefore it is necessary to take care of the new.
- If at your car a new varnish covering: to clear a place on a door where it will be pasted молдинг, gasoline and удалителем silicone.
- Otherwise on a door with an old covering. You should remove the glue rests, having left about 1 mm of a thickness. This rest is necessary as a basis for new клеющего a material.
- Watch thus not to damage a varnish covering.
- To clear a place on a door where it will be pasted молдинг.
Plastic parts in the field of gluing to wipe cleaner D 009 400 01 and to wipe dry.
- Metal (only in case on metal a new varnish covering) and plastic elements of a body to cover in the field of gluing by a first coat. For metal parts to apply праймер D 009 200 02, to plastic D 009 600.
- To put on an underside молдингов клеющий hermetic AKD 476 KD5 05 from PUR – in the middle молдинга the layer suffices gluing thickness of 4 mm.
- To put молдинг to a door, to correct and densely to press in a gluing place – especially the ends.
- Hardening time at 20°С: 4 hours.
|
|
|
|
The help: if the procedure written under instructions Audi seems too difficult, it is possible to arrive as follows: to put a thick layer on an underside молдинга transparent silicone hermetic. To press молдинг on the cleared overlay of a door and to clean superfluous hermetic. Before hermetic drying (about one day) to fix молдинг клеющей a tape. In this case молдинг keeps though and not so it is good, as serial, but nevertheless quite maintains an automatic sink. |
The bottom protective overlay
On a bottom edge of doors, and also by adjoining metal parts on the corresponding version of the car there passes a thin protective overlay. More low the removal plan.
|
|
- The parts of an overlay which are on forward wings and on back lateral parts, are pasted. Removal and installation are described in section «Removal молдинга».
- To disconnect from молдингов on doors forward and back tips and, at an open door, to remove молдинг from a percussion cap to (pull out).
|
|
|
On the main page
|