Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
Forward bumpers
Forward part of the car
Cowl
Wings
Молдинги
Doors
External rear-view mirrors
The forward and back has flown down
Cover of a luggage carrier at a sedan
Back door of the versatile person
Back bumper
The sdvizhnoj hatch
Procleaning of apertures for a water drain
The control of anticorrosive protection of the bottom of a body
Salon
Seats
+ Search of malfunctions
+ Specifications
|
External rear-view mirrors
Removal
|
|
- Electric regulation of rear-view mirrors: to take the mirror case aside.
- Now both fixing screws in a mirror leg become visible – to turn out them.
- To separate the multicontact tip directly on a mirror leg.
- Mechanical regulation of rear-view mirrors: to remove a door covering.
- To turn out the forward screws connecting the external panel of a door from boxes, both back only a few to weaken.
- Now it is possible to stretch a mirror drive between panels.
- To take the mirror case aside, to turn out fixing screws in a mirror leg.
- At installation to use corresponding fixing apertures at doors.
- Driver's door: to use a carving aperture in front below (if there are two) and behind above.
- Door of the forward passenger: to use a carving aperture in front above and behind below and above.
- Again to establish a window frame.
|
|
|
|
The help: electric window lifterа you will find the description of work and the control in the head «Devices and auxiliary devices». |
At the left: removal of a mirror by means of a wide shovel. It is recommended to put on working gloves – in case glass will break.
On the right: adjustment of a free wheeling of a mechanical drive of a rear-view mirror can be carried out, turning adjusting screws at the removed castors with longitudinal накаткой.
Mirror replacement
Glasses of mirrors keep both in электрически, and in mechanically adjustable mirrors only on latches. Removal:
|
|
- To put on working gloves in case glass will break.
- To insert from below wide шпатель or a plastic plate under glass of a mirror and to take out it from latches.
- If necessary to repeat the same operation from above.
- At installation to insert glass in directing and to press before fixing.
- In gloves to press the glass middle.
|
|
Adjustment of a drive of a mirror
Privodnye cables of mechanical regulation of mirrors can be established so that there was no too big free wheeling of adjusting castors. Very small screw-driver for this purpose is required.
|
|
- Castors with longitudinal накаткой the mechanism of regulation of external rear-view mirrors to remove in a direction upwards, if necessary to help a screw-driver.
- For приводное a direction (upwards/downwards; to the right/on the left) two answer always located the friend opposite to the friend of the screw. At one of them left, at another the right carving.
- Regulation: screw A1 cautiously to turn to the right, to those small resistance will not be felt yet.
- Screw A2 to turn to the left, to those small resistance will not be felt yet.
- Too most to repeat with bolts В1 and В2.
- To check up correctness of installation: the mirror is easily regulated, but the free wheeling remains maximum.
|
|
|
|
Helps: if glass of an external mirror shivers during a trip, means, the adjusting mechanism is established too freely – дозатянуть.
Too легкоходное regulation of mirrors leads to that already insignificant touches a sleeve to castors with longitudinal накаткой change position of mirrors. In that case it is necessary to establish it a little more tightly. |
|
On the main page
|