Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1. 4-cylinder engines
   + 3.2. Engines V6 of 3,0 l (1993-1994) and 3,4 l (since 1995)
   - 3.3. Dismantle and engine major repairs
      3.3.1. Specifications
      + 3.3.2. Major repairs
      3.3.3. Diagnostics of the engine by means of the vacuum gauge
      3.3.4. Compression check in engine cylinders
      + 3.3.5. Dismantle of the power unit
      + 3.3.6. A head of cylinders
      3.3.7. Valves
      3.3.8. Shatunno-piston group
      + 3.3.9. Коленвал
      3.3.10. The block of cylinders
      3.3.11. Хоннингование cylinders
      + 3.3.12. Rods and pistons
      3.3.13. Radical and шатунные bearings
      3.3.14. Balansirnye shaft
      3.3.15. An assembly order
      3.3.16. Piston rings
      3.3.17. Start-up of the engine after repair and обкатка
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes

3.3.13. Radical and шатунные bearings
THE GENERAL DATA

Kinds of deterioration radical and шатунных bearings

Check

Radical and шатунные bearings at engine major repairs are subject to the obligatory replacement, however the bearings which were in operation should be checked up carefully to restore the general condition of the engine at the moment of repair.

Sources of rupture of bearings of a cranked shaft are insufficient greasing because of wrong assemblage, pollution and penetration of extraneous particles, frequent overloads of the engine, corrosion, etc. Irrespective of the reason which have caused destruction of bearings, it should be eliminated.

Selection of radical bearings

If bearings of standard dimensional groups the new bearing steals up under numbers put on replaced, and also under numbers on the block of cylinders and коленвале are established.

Places of drawing of standard dimensional groups of radical bearings on 4-cylinder engines

Number on the block should coincide with number on the bearing.

Definition of number of the loose leaf on engines V6 of 3,0 l

 1. Labels 1, 2 and 3

2. An otschetnaja label

3. Labels 0, 1 or 2

Loose leaf number is defined from the table under neck numbers on the block and to number on коленвале.
Number on the block of cylinders
1
2
1
3
2
1
3
2
3
Number on коленвале
0
0
1
0
1
2
1
2
2
Loose leaf number
1
2
2
3
3
3
4
4
5

Definition of number of the loose leaf on engines V6 of 3,4 l

 1. Labels 1, 2 and 3

2. An otschetnaja label

3. Labels 0, 1 or 2

Loose leaf number is defined from the table under neck numbers on the block and to number on коленвале.
Number on the block of cylinders
1
2
3
Number on коленвале
0
1
2
0
1
2
0
1
2
Loose leaf number
1
2
3
3
3
4
2
4
5

Selection шатунных bearings

If bearings of standard dimensional groups the new bearing steals up under numbers put on replaced and on a cover of a rod are established.

After selection measure a backlash in necks (subsection 3.3.9.3, subsection 3.3.12.2 see).


On the main page