Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
- 3. Engines
   + 3.1. Four-cylinder engines
   - 3.2. Five-cylinder engines
      3.2.1. Removal and engine installation
      - 3.2.2. Dismantling and engine assemblage
         3.2.2.1. Removal and installation of a head of the block of cylinders
         3.2.2.2. Adjustment and a tension of a belt of a drive of a camshaft
         3.2.2.3. Survey, дефектовка and repair of details of a head of the block
         3.2.2.4. Removal of a camshaft and pushers of valves
         3.2.2.5. Installation of a camshaft and pushers of valves
         3.2.2.6. Removal and installation of valves
         3.2.2.7. Dismantling and assemblage of a drive of a camshaft
         3.2.2.8. Removal and flywheel installation
         3.2.2.9. Removal and installation oil картера
         3.2.2.10. Removal, check and installation of the oil pump
         3.2.2.11. Replacement of epiploons of a cranked shaft
         3.2.2.12. A cranked shaft and shatunno-piston group
   + 3.3. The diesel engine
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment

3.2.2.10. Removal, check and installation of the oil pump
PERFORMANCE ORDER
1. To remove a belt of a drive of a camshaft and виброгаситель with a cogwheel of a cranked shaft (subsection 3.2.2.7 subitem 2-5 see).
2. To remove oil картер (subsection 3.1.2.13 see).
3. To remove a cogwheel 6 camshafts (fig. the Flywheel, a cranked shaft, the oil pump see), having turned away a bolt of its fastening.
4. To remove a back cover 7 drives of a camshaft (fig. of the Detail of a drive of a camshaft see), having turned away bolts of its fastening.
5. Having unbent the ends of lock washers, to turn away two bolts, fastening the receiver of the oil pump to the block.
6. Having unbent the ends of lock washers, to turn away two bolts, fastening the receiver to the oil pump. To remove the receiver 12 and a lining 13 (fig. the Flywheel, a cranked shaft, the oil pump see).
7. To turn away bolts of fastening of the oil pump. To remove the pump 1 and a lining 2.
8. To turn away screws of fastening of a cover of the pump and to uncover.
9. To turn out редукционный the valve.
10. Pump details to clear of a dirt and to wash out in gasoline. To examine pump details. If on a cover there are wear tracks, it is necessary to replace it. Pump gear wheels can be changed on new only in pair. To replace a lining 2 pumps and a lining 13 receivers, a forward epiploon 16 cranked shaft.
11. To collect and establish the oil pump upside-down. Before запрессовкой to grease an epiploon with engine oil. If on cranked to a shaft in that place on which the epiploon worked, deepening was formed, it is necessary запрессовать an epiploon more deeply so that the working edge of an epiploon worked on a cranked shaft behind deepening. To replace lock washers of bolts of fastening of the pump and the receiver. On pump gear wheels there is a triangular label, it should be directed to a pump cover. To tighten bolts of fastening of the pump the moment: short bolts and a rack – 10 Н·м (1,0 кгс·м); long bolts – 20 Н·м (2,0 кгс·м). Bolts of fastening of the receiver to tighten the moment 10 Н·м (1,0 кгс·м).


On the main page