Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
- 9. Suspension brackets, wheels
9.1.1. Elimination of a resonance / of vibration of a cross-beam (4-cylinder models)
9.1.2. Change of a design of a forward suspension bracket
9.1.3. Полуось
9.1.4. A suspension bracket rack
9.1.5. SHRUS
9.1.6. A suspension bracket rack (all-wheel drive models)
9.1.7. SHRUS (all-wheel drive models)
+ 9.2. A back suspension bracket
+ 9.3. Wheels and tyres
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment
|
Rack of a suspension bracket / of Poluos – for 4-cylinder models
1. An epiploon
Replacement: remove a protective film and paste to a semiaxis
2. A washer
3. М8: 45 Н.м., М10: 80 Н.м.
4. Полуось, sticks together with a wheel nave
5. 65 Н.м.
6. The lever of a forward suspension bracket with the spherical hinge
7. 256 Н.м., turn off and twist only when the car costs on the earth, fix by means of glue D6 |
8. A bolt
Always replace
9. Cross-section draught
Remove from the pendular lever at noмощи a two-foot stripper
10. 30 Н.м.
11. A suspension bracket rack
12. A rigid emphasis
13 60 Н.м,
14. A cover |
Rack of a suspension bracket / of Poluos – for 4-cylinder models
1. A suspension bracket rack
At removal do not remove полуось
2. Полуось
Does not stick together with a wheel nave
For removal: turn off a bolt
Fastenings also remove it with
Naves
Turn a rack of the bearing of a nave of a wheel and accordingly a steering wheel
3. An epiploon
Remove a protective film and paste to a semiaxis
4. A washer
5. М8: 45 Н.м,
М10: 80 Н.м.
6. Cross-section draught
Remove by means of a two-foot stripper
7. 80 Н.м.
After a twisting till the demanded moment of an inhaling turn in addition on a half-turn (180 °)
Always replace with nuts of new updating
|
8. A bolt
Always replace
9. The lobby lever лодвески with the spherical hinge
At removal from a rack of the bearing of a nave of a wheel, do not expand a nest in a rack
10. A bolt and a washer
Always replace
120 Н.м., turn in addition on a turn quarter (90 °)
Turn off, only when the car costs on the earth
11. 65 Н.м.
12. A bolt
Always replace with bolts of new updating
Note installation position before removal
13. A rigid emphasis
14. 60 Н.м.
15. A cover
|
Полуось
Removal
The prevention If the car is necessary for moving after semiaxis removal, the external hinge should be established into place not to damage the wheel bearing.
At removal of the spherical hinge from a rack of the bearing of a nave of a wheel, do not expand a crack in a rack.
On cars with the 4-cylinder engine the forward suspension bracket or with a folding rack, or with not folding rack is established.
| PERFORMANCE ORDER |
| 1) ослабьте bolts of fastening of wheels |
| 2) remove a bolt or a nut of fastening of a nave of a wheel to a semiaxis (the car should stand on the earth) |
| 3) remove a washer |
| 4) remove a wheel |
| 5) remove a semiaxis flange |
| 6) remove a nut from connecting draught |
|
7) remove bolts of fastening of the lever of a forward suspension bracket / of the stabilizer of cross-section stability / of a cross-beam of a forward suspension bracket (are specified by arrows) |
| 8) lower the suspension bracket lever |
|
9) by means of a stripper, as is shown in drawing, remove полуось from a wheel nave |
|
Installation
The prevention Clear шлицы semiaxes and naves of a wheel for removal of oil, greasing and the glue rests.
| PERFORMANCE ORDER |
|
For cars with a suspension bracket with not folding rack: put glue D6 on external edge шлицов a strip about 5 mm in width (it is specified by an arrow) then establish полуось |
|
The prevention At installation of the right semiaxis be accurate and do not damage a casing on a protective plate.
Do not move the car within at least 60 minutes to allow to glue D6 to harden.
|
On the main page
|