Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

9.1.5. SHRUS

THE GENERAL DATA

Полуось (4 cylinder models)

1. An internal SHRUS External diameter for cars with the 4-cylinder engine: 100мм 2. Полуось There are semiaxes of various length depending on transmission type 3. A lock ring Establish in a ring flute on a semiaxis (it is not visible at the established hinge) 4. An external SHRUS Remove only entirely Installation: establish the hinge On полуось with the help киянки So that it was possible To establish a lock ring 5. A persistent washer 6. A convex washer 7. A shlangovyj clip 8. A cover Check up on presence of cracks and wear tracks 9. A clip 10. A cover with a cover Check up on presence of cracks and wear tracks Remove with the help оправки Before installation on the SHRUS cover an obverse surface with glue D3 11. A convex washer There are 2 types: 1. With internal шлицами 2. With external шлицами At replacement establish a washer of the same type 12. An epiploon Replacement: remove a protective film and paste on the hinge 13. A lock ring

---

The prevention

Semiaxis greasing on cars with the 4-cylinder engine: grease an internal and external SHRUS (the hinge of equal angular speeds) with 90 grammes of greasing G-6 everyone.

---

Полуось (5-cylinder models)

1. A convex washer There are 2 types: 1. With internal шлицами 2. With external шлицами At replacement establish a washer of the same type 2. A lock ring Establish in a ring flute on a semiaxis (it is not visible at the established hinge) 3. An external SHRUS Remove only entirely Installation: establish the hinge on полуось with the help киянки so that it was possible to establish a lock ring 4. A persistent washer 5. A convex washer 6. A shlangovyj clip 7. A cover Check up on presence of cracks and wear tracks 8. A clip 9. Полуось 10. A cover with a cover Check up on presence of cracks and wear tracks Remove with the help оправки Before installation on the SHRUS cover an obverse surface with glue D3 11. An internal SHRUS External diameter: For cars with the 4-cylinder engine: 100 mm For cars with the 5-cylinder engine: 108 mm Quattro: 100 mm 12. An epiploon Replacement: remove a protective film and paste on the hinge 13. A lock ring

---

The prevention

Semiaxis greasing on cars with 5-cylinder двигагелем: grease an internal SHRUS in 120 grammes of greasing G6 and external – 90 grammes.

---

The modified SHRUS of a semiaxis

1. Полуось with internal the SHRUS Is on sale as the spare part In the complete set a cover and greasing Grease at cover replacement Grease with 250 grammes of greasing G 000 604 2. A clip Stainless steel Always replace 3. A cover Check up on presence of cracks and deterioration For replacement remove the SHRUS For installation grease a fillet on a semiaxis a little and accurately put on a cover by means of a plastic wedge 4. A clip Stainless steel Always replace

5. A cover Check up on presence of cracks and wear tracks For installation remove an external SHRUS 6. A clip Stainless steel Always replace 7. A tightening ring Always replace Establish in a ring flute on the hinge of equal angular speeds 8. An external SHRUS Replace entirely Grease with 90 grammes of greasing G 000 602: 50 gramme on a cover, 40 gramme – on the SHRUS Grease at cover replacement Installation: establish the hinge on полуось with the help киянки so that the lock ring got to a ring flute

Convex and persistent washers, installation position

1. A lock ring 2. A persistent washer 3. A convex washer

Removal and installation the SHRUS

PERFORMANCE ORDER

1) tighten a clip 2) at installation the cover can be pressed that further at car operation can lead to occurrence of folds; After installation for a second slightly open the end of a cover with smaller diameter to level pressure inside and outside – such ventilation of a cover will prevent occurrence of folds. 3) remove an external SHRUS: Clamp полуось in a vice Remove a cover Twist the special tool while the SHRUS will not be removed from a semiaxis 4) remove a lock ring internal the SHRUS 5) remove an internal SHRUS   6) establish a lock ring internal the SHRUS: Establish the hinge against the stop Establish a lock ring 7) establish a convex washer, note its position Semiaxes with the modified hinges of equal angular speeds are established on cars with a 4-speed automatic transmission 097 and the engine capacity of 130 h.p. 8) tighten clips 9) remove an external SHRUS: Clamp полуось in a vice Remove a cover 10) establish a cover the SHRUS on полуось: Remove locking ring (it is specified by an arrow) Twist bolt М16 of the tool 3207 while the SHRUS will not be removed from a semiaxis