Citroen Xantia
+ Introduction
+ The operation manual
- Routine maintenance
+ Weekly checks
- Car routine maintenance - petrol models
Regular service
Replacement of impellent oil and the oil filter
Check of a condition of hoses, and revealing of sources of leaks
Check of adjustment of coupling
Check of level ATF
Suspension bracket and steering drive
Check of a condition of protective covers of power shafts
Reading of memory of the block of self-diagnostics
Replacement of the dust removal filter (model with К/В)
Check of a condition of a coolant of a central air of air
Replacement of spark plugs
Check of a condition of system of ignition
Check and adjustment of turns and quality of a mix of idling
Check of serviceability of functioning of systems of decrease in toxicity of the fulfilled gases
Check of a condition and replacement of a belt of a drive of auxiliary units
Greasing of the mechanism of a drive of deenergizing of coupling
Condition check колодок brake mechanisms of forward and back wheels
Check of serviceability of functioning and adjustment of a lay brake
Trial runs
Replacement трансмиссионной liquids АТ
Greasing of locks and loops
Replacement of a filtering element of an air cleaner
Level check трансмиссионного oils (models with РКПП)
Replacement of the fuel filter
Replacement of hydraulic liquid LHM and the returnable filter
Check of a condition of brake supports, disks and hydraulic hoses
Replacement of a belt of drive ГРМ
Replacement of a cooling liquid
+ Car routine maintenance - diesel models
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes
|
Trial runs
THROUGH EACH 30 000 KM (18 000 MILES) RUN
Devices and electric equipment
|
|
|
1. Check up serviceability of functioning of monitors and an electric equipment.
2. Make sure of adequacy of indications of measuring instruments, serially include all consumers of the electric power. |
|
Steering and suspension bracket
|
|
|
1. Try to reveal any sort the unusual sensations arising at driving. Estimate course stability of a vehicle.
2. Pay attention to unusual noise and the vibrations published during movement by components of a suspension bracket and a steering drive.
3. Estimate controllability of the car - the steering wheel should rotate freely, without an excessive weak point and jerks. The suspension bracket during fulfilment of turns and movement on roughnesses of a road covering should not publish any extraneous noise. |
|
Transmissionnaja line
|
|
|
1. Try to estimate efficiency of return of the engine and quality of transfer of rotation by components of coupling, a transmission and power shafts.
2. Pay attention to any unusual noise published by the engine and components трансмиссионной of a line.
3. Check up stability of single turns of the engine. Estimate stability of turns during an acceleration.
4. On models with РКПП make sure of smoothness and noiselessness of operation of coupling. The pedal course should not be excessive, and its squeezing to lead to occurrence of extraneous sounds. Make sure of ease and noiselessness of inclusion of all transfers - the control lever should move freely, without jerks and закусываний.
5. On models with АТ make sure of serviceability of functioning of the lever of the selector and adequacy of switching of a box.
6. Listen to the sounds which are starting with a forward part of the car at a slow movement in a circle with a steering wheel turned out against the stop. Check should be made for both directions of turn of wheels. Presence of a metal gnash will testify to deterioration of hinges of equal angular speeds (SHRUS) of power shafts. In case of revealing of signs of deterioration the defective SHRUS is subject to replacement (Power shafts see the Head). |
|
Check of serviceability of operation and efficiency of functioning of brakes
|
|
|
1. Make sure of preservation of course stability of the car during braking. Sharp braking should not cause premature blocking of wheels.
2. Make sure of absence of occurrence of vibrations in a steering wheel during car braking.
3. Check up serviceability of functioning of a lay brake. The car should be kept reliably on a bias even at moderate raising of the lever. |
|
|
On the main page
|