Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1. 4-cylinder engines
   + 3.2. Engines V6 of 3,0 l (1993-1994) and 3,4 l (since 1995)
   - 3.3. Dismantle and engine major repairs
      3.3.1. Specifications
      - 3.3.2. Major repairs
         3.3.2.1. Alternatives
         3.3.2.2. An order of dismantling of the engine
      3.3.3. Diagnostics of the engine by means of the vacuum gauge
      3.3.4. Compression check in engine cylinders
      + 3.3.5. Dismantle of the power unit
      + 3.3.6. A head of cylinders
      3.3.7. Valves
      3.3.8. Shatunno-piston group
      + 3.3.9. Коленвал
      3.3.10. The block of cylinders
      3.3.11. Хоннингование cylinders
      + 3.3.12. Rods and pistons
      3.3.13. Radical and шатунные bearings
      3.3.14. Balansirnye shaft
      3.3.15. An assembly order
      3.3.16. Piston rings
      3.3.17. Start-up of the engine after repair and обкатка
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes





3.3.2.2. An order of dismantling of the engine
THE GENERAL DATA

The krivoshipno-shatunnyj mechanism and piston group of 4-cylinder engines

1. A ring компрессионное the top
2. Disks маслосъемного rings
3. A flywheel
4. A bolt
5. A rod
6. Shatunnye loose leaves
7. A rod cover
8. An epiploon
9. An intensifying plate
10. The holder
11. The detonation gauge
12. A perepusknoj branch pipe of cooling
13. The fuel filter
14. A lining
15. A hose
16. A support left
17. The radical loose leaf
18. A cover
19. A persistent ring
20. Коленвал
21. An asterisk
22, 26. A persistent plate
23. An asterisk
24, 25. A balansirnyj shaft
27. A washer
28. A support right
29. A drain stopper
30. The oil filter
31, 33. A ring
32. The union
34. A lock ring
35. A finger
36. A broad ring
37. Bottom компрессионное a ring

The krivoshipno-shatunnyj mechanism and piston group of engines V6 of 3,0 l

1. The detonation gauge
2. A perepusknoj branch pipe of cooling N1
3. For а/м from a manual transmission
4. A flywheel
5. An intensifying plate
6. An epiploon
7. The holder
8. For а/м with automatic transmission
9, 11. A remote washer
10. A leading disk
12. The reduktsionnyj valve
13, 15. A lining
14. Маслоохладитель
16, 18. A hose

17. The union
19. The pressure gauge
20. To tighten динамометрическим a key
21. A skeleton of covers
22, 25. Persistent half rings
23. The radical loose leaf
24. Коленвал
26. An adjusting bar of the generator
27. The block of cylinders
28. A rod cover
29. Shatunnye loose leaves
30. A rod
31. A finger
32. Rings
33. The piston
34. A bolt

The krivoshipno-shatunnyj mechanism and piston group of engines V6 of 3,4 l

1. A ring компрессионное the top
2. A ring компрессионное the bottom
3. Disks маслосъемного rings
4, 18. A lock ring
5. The plug
6. A rod
7. Shatunnye loose leaves
8. A rod cover
9. An epiploon
10. The holder
11. The block of cylinders
12. Коленвал
13, 17. Radical loose leaves
14. A skeleton of covers
15, 16. Persistent half rings
19. A finger
20. The piston
21. A dilator маслосъемного rings

The following order of full dismantling of the engine is recommended:

 – Collectors;
 – Covers of a head of cylinders;
 – A chain cover, a chain, drive details (4-cylinder engines);
 – Covers of a gear belt a belt, asterisks (on engines V6);
 – A head () cylinders;
 – The pallet;
 – The oil pump;
 – балансирный a shaft (4-cylinder engines);
 – Rods and pistons;
 – Epiploons;
 – коленвал.

On the main page