Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of position of a pedal of a brake
   10.3. The main cylinder of a brake
   10.4. The brake mechanism of a forward wheel of mark Teves
   10.5. The brake mechanism of a forward wheel of mark GIRLING
   10.6. A brake disk
   10.7. The case скобы and the piston
   10.8. The drum-type brake mechanism of a back wheel
   10.9. A brake drum
   10.10. The wheel brake cylinder
   10.11. The disk brake mechanism of a back wheel
   10.12. A pressure regulator
   + 10.13. A lay brake
   10.14. Antiblocking system of brakes (ABS)
   10.15. Prorolling of brake system
+ 11. A body
+ 12. An electric equipment

10.7. The case скобы and the piston
THE GENERAL DATA

Brake скоба firms Teves

1 – the basis скобы;
2 – a protective cover;
3 – the piston;
4 – a sealing ring;
5 – the case скобы;
6 – the rubber plug;
7 – the plastic plug;
8 – a directing finger;
9 – грязезащитный a cap;
10 – protective колпачек;
11 – the valve of release of air

PERFORMANCE ORDER
1. To establish the car on a lay brake.
2. To establish basic бруски under back wheels.
3. To weaken an inhaling of bolts of fastening of a forward wheel.
4. To raise and establish on support a forward part of the car.
5. To remove a wheel.
6. To turn away a fastening nut, to separate brake hoses and to muffle an aperture of the brake hose which has remained on the car.
7. To turn away two directing fingers (fig. Brake скоба firms Teves see), having removed preliminary грязезащитные caps, and to remove the case скобы.

Dismantling

PERFORMANCE ORDER
1. To remove a protective cover (fig. Brake скоба firms Teves see) piston. To clamp the case скобы in a vice with overlays of sponges from soft metal. To take out the piston from the cylinder, having submitted compressed air through the union for a brake hose and holding the piston with a hand or having enclosed a wooden lath.
2. To take out a sealing ring from the cylinder, using a wooden shovel. Application of metal subjects is not recommended, as it can lead to damage проточки the cylinder under a sealing ring.
3. To unscrew the prorolling valve.
4. To wash out the piston and the cylinder a fresh brake liquid.

Survey and дефектовка case details скобы

PERFORMANCE ORDER
1. To examine a working surface of the piston and the cylinder. At presence on working surfaces of the piston and the cylinder of wear tracks, corrosion, bowls and забоин to replace the case скобы complete with the piston.
2. The sealing ring and a protective cap of the piston are subject to obligatory replacement.

Assemblage

PERFORMANCE ORDER
1. To grease an internal surface of the cylinder with a fresh brake liquid.
2. To grease a new sealing ring with a fresh brake liquid and to insert in проточку the cylinder.
3. To grease a new protective cover with a fresh brake liquid and to insert it in проточку on the piston.
4. To insert the piston into the cylinder effort of fingers, without applying any tools, and by means of a screw-driver accurately to insert an external edge of a protective cover in проточку the cylinder.
5. To grease the valve of prorolling with a fresh brake liquid and to screw it in the case скобы.

Installation

PERFORMANCE ORDER
The case скобы in an order, the return to removal is established. Thus to wrap two directing fingers the moment 25 Н·м (2,5 кгс·м), holding thus directing finger with a key. After installation to pump over подвергшийся to repair a brake (subsection 10.15 see).


On the main page