Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Тойота 4Раннер
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Specifications
   2.2. An arrangement of knots and units
   + 2.3. Periodicity of maintenance service and kinds of procedural works
   2.4. Intensive service
   + 2.5. Check of level of liquids
   2.6. Check of tyres
   2.7. Check of level of a liquid in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Care of the battery
   2.11. Check of system of cooling
   2.12. Check of a condition of the hoses located in a motor compartment
   2.13. Screen wiper brushes
   2.14. Shift of wheels
   2.15. Check of a suspension bracket of a steering
   2.16. Greasing of a running gear, suspension brackets, a steering and body details
   2.17. Exhaust system check
   2.18. Check of level of oil in a manual transmission
   2.19. Check of level of oil in a distributing box
   2.20. Check of level of oil in a reducer
   2.21. Check of seat belts
   2.22. Check of covers of semiaxes
   2.23. A ventilation zolotnik картера
   2.24. A filtering element of the air filter
   2.25. Belts of a drive of hinged units
   2.26. Check of fuel system
   2.27. Check of deterioration of brakes
   2.28. Check and adjustment of pedals of coupling (brake)
   2.29. Replacement of candles
   2.30. Check and adjustment of backlashes in valves
   2.31. Replacement of the fuel filter
   2.32. High-voltage wires, бегунок and a distributor cover
   2.33. Care of cooling system
   2.34. Naves and bearings of forward wheels
   2.35. Liquid replacement in automatic transmission and the filter
   + 2.36. Oil replacement
   2.37. Check of a tank with an absorber
   2.38. Check of the valve of system recycling
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes

2.25. Belts of a drive of hinged units
THE GENERAL DATA

Characteristic kinds of deterioration клиновидных belts

1. Strip deterioration of a lateral surface

2. Обугливание

3. Cracks


4. Stratification


5. Brightness


6. Замасливание


7. An anguish

Characteristic kinds of deterioration of belts with the goffered profile

1. Comprehensible

2. Cracks

3. Неприемлимый

4. Loss of 2 and more edges

5. Parallel cracks

Check

PERFORMANCE ORDER
1. The quantity of belts of a drive depends on a car complete set. Belts have клиновидное section and are used for a drive of the generator, the hydraulic booster of a wheel, the pump of a cooling liquid and the conditioner. One belt as a rule is used for a drive of several units.
2. Open a cowl and check up fingers a condition of belts from two parties, overwinding belts (fig. Characteristic kinds of deterioration клиновидных belts see).
3. Check up a belt tension on deflection size in the middle between pulleys. If distance centre to centre pulleys of 180-300 mm the deflection has to be 6,5 mm, and at distance centre to centre 300–400 mm the deflection should be 13 mm (1 – a ruler, 2 – брусок, 3 – a deflection) for клиновидных belts and 6,5 mm for belts with the goffered profile (fig. Characteristic kinds of deterioration of belts with the goffered profile see).

Adjustment

PERFORMANCE ORDER
1. The belt is regulated by two bolts – adjusting () and axial () which it is necessary to weaken and displace a roller or a pulley of a mobile part. After adjustment check up a belt tension, if necessary again ослабьте bolts and adjust a tension. Upon termination of adjustment bolts tighten, without making the big effort.
2. On cars of early releases the adjusting bolt is absent also a roller (or a pulley) are displaced by the auxiliary lever (mount).

Replacement
PERFORMANCE ORDER
1. For belt replacement execute the same preliminary procedures, as for adjustment then remove a belt. All belts are recommended to be changed simultaneously.
2. Before removal designate each belt and a corresponding pulley.
3. At acquisition compare a new belt to the replaced.
4. Adjust a belt tension.


On the main page