Тойота 4Раннер
+ 1. The maintenance instruction
- 2. Maintenance service
2.1. Specifications
2.2. An arrangement of knots and units
+ 2.3. Periodicity of maintenance service and kinds of procedural works
2.4. Intensive service
+ 2.5. Check of level of liquids
2.6. Check of tyres
2.7. Check of level of a liquid in automatic transmission
2.8. Liquid level in system of a hydrodrive of a steering
2.9. Oil replacement in the engine and the oil filter
2.10. Care of the battery
2.11. Check of system of cooling
2.12. Check of a condition of the hoses located in a motor compartment
2.13. Screen wiper brushes
2.14. Shift of wheels
2.15. Check of a suspension bracket of a steering
2.16. Greasing of a running gear, suspension brackets, a steering and body details
2.17. Exhaust system check
2.18. Check of level of oil in a manual transmission
2.19. Check of level of oil in a distributing box
2.20. Check of level of oil in a reducer
2.21. Check of seat belts
2.22. Check of covers of semiaxes
2.23. A ventilation zolotnik картера
2.24. A filtering element of the air filter
2.25. Belts of a drive of hinged units
2.26. Check of fuel system
2.27. Check of deterioration of brakes
2.28. Check and adjustment of pedals of coupling (brake)
2.29. Replacement of candles
2.30. Check and adjustment of backlashes in valves
2.31. Replacement of the fuel filter
2.32. High-voltage wires, бегунок and a distributor cover
2.33. Care of cooling system
2.34. Naves and bearings of forward wheels
2.35. Liquid replacement in automatic transmission and the filter
+ 2.36. Oil replacement
2.37. Check of a tank with an absorber
2.38. Check of the valve of system recycling
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes
|
Lift the car and remove wheels.
DISK BRAKES
| PERFORMANCE ORDER |
|
1. Колодки it is possible to check up through a window in a support (it is specified by an arrow). |
|
2. Measure a thickness () frictional overlays, and if a thickness less specified in subsection 2.1 replace Pads. |
| 4. If there are any doubts concerning a normal state of overlays Pads it is necessary to remove. |
| 5. At the same time check up a disk condition. Measure a thickness of a disk and check up a surface condition. If the thickness is less than norm a disk replace. Insignificant defects of a surface leave the polishing, strongly worn out disk replace. |
|
6. Check up подтекание liquids from a hose in the specified place (marksman) and tubes of a hydrodrive of brakes. Check up reliability of an inhaling of connections. All found out defects immediately eliminate. |
|
DRUM-TYPE BRAKES
| PERFORMANCE ORDER |
| 1. Remove drums (subsection 8.6 see). |
| 2. Check up a thickness of frictional overlays. If their thickness (or distance to heads of rivets) is less 1,6 mm, or there are traces замасливания or serious damages Pads replace. |
| 3. Check up a condition of springs and a backlash regulator between колодками and drums. |
|
4. Check up подтекание liquids from the wheel cylinder, having unbent a dustproof cover. At detection of a leak the cylinder replace. |
| 5. Check up a condition of drums. Minor defects polish a skin, if necessary drums pierce. |
| 6. Establish all removed details and lower the car. Wheel nuts tighten with the set moment. |
|
CHECK OF THE VACUUM AMPLIFIER
| PERFORMANCE ORDER |
| 1. On the idle engine press some times a brake pedal, the course of a pedal of a brake thus should not to change. |
| 2. Press a pedal and start the engine, all time. After start-up of the engine the pedal should be displaced a little forward. |
| 3. Press a pedal of a brake and stop the engine. Within approximately 30 seconds, the pedal should keep the position. |
| 4. Again start the engine, later 1 mines stop and press some times a pedal. The course of a pedal with each pressing should decrease. |
| 5. If work of the vacuum amplifier differs from described above the vacuum amplifier in this case is subject to replacement (see subsection 8.13). |
|
CHECK AND ADJUSTMENT OF THE MANUAL BRAKE
| PERFORMANCE ORDER |
| 1. Translate the transmission lever in neutral position. Having made moderate effort the lever of a manual brake, count up quantity of clicks of a full speed of the lever. If the quantity of clicks does not correspond to norm the manual brake should be adjusted. |
| 2. Check up work of a manual brake, having established the car on an abrupt slope. The adjustment order is described in подразделe 8.11. |
|
|
On the main page
|