Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
+ 3.1. 4-cylinder engines
- 3.2. Engines V6 of 3,0 l (1993-1994) and 3,4 l (since 1995)
3.2.1. Specifications
3.2.2. Repair kinds, выполняемыe without removal of the engine from the car
3.2.3. Installation of the piston of 1st cylinder in ВМТ a compression step
3.2.4. Covers of heads of cylinders
3.2.5. A soaking up collector
3.2.6. Final collectors
3.2.7. A belt of an asterisk of cam-shafts
3.2.8. A forward epiploon коленвала
3.2.9. Epiploons of cam-shafts
3.2.10. Cam-shafts and pushers
3.2.11. Heads of cylinders
3.2.12. The oil pallet
3.2.13. The oil pump
3.2.14. A flywheel (a leading disk of the hydrotransformer)
3.2.15. A back epiploon коленвала
3.2.16. Engine mount details
+ 3.3. Dismantle and engine major repairs
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes
|
The masljannyj pallet and adjacent details on the engine of 3,0 l
1. A cover of the oil pump
2. A leading gear wheel
3. A conducted gear wheel
4. The case
5. An epiploon
6. A sealant
7. The reduktsionnyj valve |
8. A spring
9, 12, 15, 19. A lining
10. For rear-wheel а/м
11, 17. Маслоотражатель
13, 16. Маслоприемник
14. For all-wheel drive а/м
18. The pallet |
The masljannyj pallet and adjacent details on the engine of 3,4 l
1. A perepusknaja pipe with a wire of the gauge of a detonation
2. For automatic transmission
3. A leading disk
4, 5. Remote linings
6. A back plate
7. A flywheel
8, 23. An engine arm
9, 20. A sealant
10. The union маслоохладителя
11. A lining
12. A hollow bolt
13. Маслоохладитель
14. The gauge of emergency pressure of oil
15. Маслоприемник
16. The pallet |
17. A stopper
18. A starter cable
19. The oil pump
21. A generator arm
22. An epiploon
24. An inlet branch pipe of a cooling liquid
25. The thermostat
26. A drain stopper
27. The detonation gauge
28. The pump of a cooling liquid
29. An arm
30. Маслоотражатель
31. The union of the oil filter
32. The oil filter |
The prevention For pallet removal on all-wheel drive cars it is required to dismantle semiaxes and a forward reducer. Therefore for pallet removal on these cars it is recommended to remove the engine as this operation is slightly easier.
Removal
| PERFORMANCE ORDER |
| 1. Remove mud guards of the engine. |
| 2. Disconnect the battery from weight. |
| 3. Lift the car. |
| 4. On all-wheel drive cars remove semiaxes and a forward reducer. |
| 5. Merge oil and remove the oil filter. |
| 6. Remove a gear belt. |
| 7. Remove the bottom casing of a flywheel. |
| 8. Turn away bolts and remove the oil pallet. If necessary displace easy blows. |
|
Installation
| PERFORMANCE ORDER |
| 1. Remove from demountable planes of the block of cylinders and the pallet the consolidation rests. Wash out condensed planes solvent. |
| 2. Be convinced of cleanliness of carving apertures in the block of cylinders. |
| 3. Check up presence on a demountable plane of the pallet of deformations, especially about apertures under bolts. If necessary отрихтуйте a plane a hammer. |
| 4. Establish маслоотражатель (if acted in film). |
| 5. Check up a condition маслоприемника, presence on it of cracks and a contamination of the filter of rough clearing. |
| 6. Put the platen of hermetic in diameter about 3 mm on a condensed plane of the pallet. |
| 7. Cautiously establish the pallet and wrap bolts. In three-four receptions tighten bolts of the pallet with the set moment, beginning an inhaling in the central part. |
| 8. Further assemblage are carried out upside-down. Fill in oil in the engine and replace the filter. Replace linings of an exhaust pipe of the muffler. |
| 9. Start the engine and be convinced of absence of leaks. |
|
|
On the main page
|