Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
- Engine repair
   + The repair procedures which are not demanding extraction of the engine from the car - petrol engines
   - The repair procedures which are not demanding extraction of the engine from the car - diesel engines
      Measurement компрессионного pressure and engine check on tightness
      Fixing cranked / distributive shaft and ТНВД for the purpose of prevention of casual hit of valves in contact to pistons in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers газораспределительного a belt
      Belt of drive ГРМ - the general information, removal, check of a condition and installation
      Removal and installation of cogwheels of a belt of drive ГРМ
      Removal and installation of components of the right support of the power unit and натяжителя газораспределительного a belt
      Removal and installation of an intermediate roller газораспределительного a belt
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment клапанных backlashes
      Removal and installation of a head of cylinders
      Removal and pallet installation картера
      Removal, check of a condition and installation of the oil pump with приводной a chain
      Replacement of epiploons
      Gauges of level, pressure and temperature of impellent oil - the general information
      Removal, check of a condition and installation of a flywheel/privodnogo of a disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
      Removal and installation маслоохладителя
   + Removal and engine major repairs
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Replacement of epiploons

The right epiploon of a cranked shaft

 PERFORMANCE ORDER

1. Remove a cogwheel of a cranked shaft (Removal and installation of cogwheels of a belt of drive ГРМ see).
2. Measure and write down landing depth of an epiploon.

3. By means of a suitable hook take an epiploon from the casing. Alternatively, drill or pierce in a face surface of an epiploon pair of apertures, screw in them саморезы and take an epiploon, having grasped nippers heads of screws.

4. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to lead to failure of a new epiploon.
5. Grease sponges of a new epiploon with pure impellent oil, then accurately plant it on former depth in a nest in a casing (the opened end inside). In quality оправки take advantage of a replaceable head of the corresponding size or a piece of a pipe of suitable diameter (оправка should rest only against firm external edge of a face surface of an epiploon). For epiploon protection wind a pin of a cranked shaft with a thin adhesive tape and plant on it assemblage of a casing with an epiploon.
6. Remove an adhesive tape.
7. Establish into place a cogwheel of a cranked shaft (Removal and installation of cogwheels of a belt of drive ГРМ see).

The left epiploon of a cranked shaft

 PERFORMANCE ORDER

1. Remove a flywheel/privodnoj a disk (Removal, check of a condition and installation of a flywheel/privodnogo of a disk see).
2. Execute the procedures described in subsection the Right epiploon of a cranked shaft, subitem 2-6 with that difference that this time the epiploon is put by external sponges outside. If sponges at epiploon installation are turned out, straighten them by means of a suitable hook. Try not to damage an epiploon.
3. Establish into place a flywheel/privodnoj a disk (Gauges of level, pressure and temperature of impellent oil - the general information see).

The right epiploon of a camshaft

 PERFORMANCE ORDER

1. Remove a camshaft cogwheel (Removal and installation of cogwheels of a belt of drive ГРМ see). In effect, there is necessity of full removal газораспределительного no belt, however it is not necessary to forget about high probability of pollution by its oil.

2. Having hooked a suitable hook, take an epiploon from the casing. Alternatively, the epiploon can be taken with the help саморезов (the subsection the Right epiploon of a cranked shaft, item 3 see).

3. Carefully clear a casing of an epiploon and a surface of a pin of a camshaft.
4. Grease sponges of a new epiploon with pure impellent oil and plant it on a shaft pin (the opened end forward). For protection of sponges it is necessary to wind a pin with an adhesive tape preliminary.
5. By means of approaching оправки запрессуйте an epiploon in the casing заподлицо with a face surface of a head of cylinders. Take advantage of bolt М10 which should be screwed in a carving aperture in a shaft end face, washers and a piece of a pipe approaching on diameter.
6. Establish into place a camshaft cogwheel (Removal and installation of cogwheels of a belt of drive ГРМ see).
7. If removed, establish газораспределительный a belt (the Belt of drive ГРМ - the general information, removal, check of a condition and installation see).

 

The left epiploon of a camshaft

Consolidation of the left pin of a camshaft is made means of the sealing ring planted in a flange of a face plate. The epiploon is not provided. Replacement of a sealing ring is made by отболчивания plates from a head of cylinders.

On the main page