Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
- Engine repair
   + The repair procedures which are not demanding extraction of the engine from the car - petrol engines
   - The repair procedures which are not demanding extraction of the engine from the car - diesel engines
      Measurement компрессионного pressure and engine check on tightness
      Fixing cranked / distributive shaft and ТНВД for the purpose of prevention of casual hit of valves in contact to pistons in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers газораспределительного a belt
      Belt of drive ГРМ - the general information, removal, check of a condition and installation
      Removal and installation of cogwheels of a belt of drive ГРМ
      Removal and installation of components of the right support of the power unit and натяжителя газораспределительного a belt
      Removal and installation of an intermediate roller газораспределительного a belt
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment клапанных backlashes
      Removal and installation of a head of cylinders
      Removal and pallet installation картера
      Removal, check of a condition and installation of the oil pump with приводной a chain
      Replacement of epiploons
      Gauges of level, pressure and temperature of impellent oil - the general information
      Removal, check of a condition and installation of a flywheel/privodnogo of a disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
      Removal and installation маслоохладителя
   + Removal and engine major repairs
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of covers газораспределительного a belt

Removal

The top forward cover (model of early years of release)

 PERFORMANCE ORDER

1. If dismantle of covers is made for the purpose of replacement газораспределительного a belt, remove an arm of fastening of the right support of the power unit to a body (Removal and installation of components of the right support of the power unit and натяжителя газораспределительного a belt see) for the purpose of expansion of working space.
2. Release the top clamp of a cover.

3. Having hooked a screw-driver, liberate the bottom lock uvula, lift a cover upwards and remove it from the engine.

The top back cover (model of early years of release)

 PERFORMANCE ORDER

1. Remove the top forward cover (see above).

2. Release two clamps, uncover fixing hairpins on a forward wall of the engine and lift it upwards. The working space extremely ограниченно, therefore for the purpose of its expansion will be preliminary reasonable to dismantle the carburettor of a corresponding support of the power unit (Removal and installation of components of the right support of the power unit and натяжителя газораспределительного a belt see).

The top forward cover (model of last years of release)

 PERFORMANCE ORDER

1. Give fixing the screw with a nut and uncover the engine.

The top back cover (model of last years of release)

 PERFORMANCE ORDER

1. Remove a forward cover (see above), then turn out fixing bolts and remove a back cover.

The bottom cover (model of early years of release)

 PERFORMANCE ORDER

1. Remove a pulley of a cranked shaft (Removal and installation of a pulley of a cranked shaft see).

2. Turn out two fixing bolts and remove the bottom cover газораспределительного a belt from the engine.

The bottom cover (model of last years of release)

 PERFORMANCE ORDER

1. Remove a pulley of a cranked shaft (Removal and installation of a pulley of a cranked shaft see).
2. Remove both top covers (see above).
3. Give fixing nuts and bolts and remove the bottom cover.

Installation

Installation is made in an order, the return to a dismantle order. Track correctness of placing of covers and reliability of a tightening of fixture (Specifications see).

On the main page