Citroen Xantia

1. Prop up противооткатными boots back wheels, then поддомкратьте redock of the car and establish it on props. Translate the selector lever in position N.
2. Remove the battery with the pallet and a basic plate (the engine Electric equipment see the Head).
3. Remove a thermofilter () systems of release of the fulfilled gases for the purpose of providing of access to the basis of assemblage of the lever of the selector of transfers (see the Head of the Power supply system and release). On some models it is necessary to remove also an inlet air line () (see the Head of the Power supply system and release).
4. From the end turned to transmission drive a cable turn out two screws of fastening of a cover of a cable to its basic arm. Accurately disconnect a tip of a cable from the spherical hinge of the lever of a choice of transfers.

Do not suppose change of position of the lever of a choice after a detachment from it drive a cable! As an additional safety measure mark a lever starting position rather картера transmissions.

5. Moving back along a cable, liberate it from intermediate clamps. Try to remember a route of a lining of a cable properly.
6. In car salon accurately having hooked, remove from the central console the panel of facing of the lever of the selector of transfers (address to the Head the Body and salon furnish).
7. Turn out screws of fastening of the handle on a lever rod. Squeeze out рычажок a clamp, turn the handle under 90 ° counter-clockwise, lift assemblage upwards, then turn under 90 ° clockwise for the purpose of liberation of the button of a clamp from an executive rod of the lever. After handle removal take from it the button of a clamp with a spring.
8. Give four nuts of fastening of assemblage of the lever to a floor.
9. Under the car disconnect assemblage of the lever from кузовной panels and remove it from the car, remembering a route of a lining of a cable.
10. Having laid lever assemblage on a workbench, separate from the lever basis a protective cover and shift it along a cable.
11. Loosen the a nut of fastening of a cover of a cable, then remove a fixing clamp. Accurately having hooked, disconnect a tip of a cable from the spherical hinge in the basis of the lever of the selector.
12. Attentively examine cable assemblage on presence of signs of damage of a cover and a core wipe. Check up serviceability of functioning of a cable: the core should move freely in a cover. Remember that after installation in regular position, a cable functions with much bigger resistance. In case of revealing of the slightest signs of malfunction replace assemblage.

1. Slightly grease with greasing on a basis дисульфида molybdenum open sites of the core of a cable, spherical hinges of levers and fixing mechanism of the lever.
2. Pass a cable in a casing of the lever of the selector. Track, the flange of a cover of a cable the apertures has got on reciprocal ledges of a casing. Fix a cable a clamp, track, that the external ends of the last have entered in the correct image into gearing with reciprocal grooves in a lever casing while the internal ends have appeared hooked for the casing basis. Tighten a fixing nut of a cover of a cable.
3. Strongly fix a core tip on the spherical hinge of the lever. Return in regular position on the basis of the lever a protective cover.
4. Having tracked correctness of a lining of a cable, get the lever from below on the regular place.
5. Involve lever assemblage in salon and tighten four fixing nuts.
6. Establish in the handle of the lever the button and a clamp spring. Completely drown the button in the handle. Keeping the button drowned, put on the handle a rod of the lever and, slightly having pressed, turn on 90 ° clockwise, then back for the purpose of input of the button of a clamp in gearing with an executive rod. Release the button, then screw and tighten four fixing screws.
7. Under the car, moving along a cable, fix it in all provided intermediate clamps and directing. Place assembly скобу cable covers on a basic arm on картере АТ, screw and tighten fixing bolts.
8. Make sure that levers of the selector and a choice of transfers are in position N, adjust приводной a cable and connect it to the choice lever on transmission (subitem 4-6 in section Adjustment drive a cable of a choice of transfers АТ see).
9. Establish into place a thermofilter () systems of release of the fulfilled gases (see the Head of the Power supply system and release), then lower the car on the earth.
10. Establish all other components acting in film for the purpose of providing of access.