Citroen Xantia

1. Prop up противооткатными boots back wheels and translate the selector lever in position “N”. Поддомкратьте redock of the car also establish it on props. Remove both lobbies of a wheel.
2. Merge from transmission ATF (address to the Head Routine maintenance), then screw into place and strongly tighten drain stoppers.
3. Open the gate of dump of a regulator of pressure and translate a control lever suspension bracket position in position LOW (the Uniform hydraulic system see the Head).
4. Remove a casing of an air cleaner and-or an inlet air line (see the Head of the Power supply system and release).
5. Remove the tank of a hydraulic liquid (the Uniform hydraulic system see the Head).
6. Remove the battery with the pallet and a basic plate (the engine Electric equipment see the Head).
7. Remove a starter (the engine Electric equipment see the Head).
8. Remove the components established at the left on a head of cylinders, including the vacuum tank and the valve of stabilisation of turns of idling.
9. At a corresponding complete set give fixing nuts and remove hydraulic modulator ABS. Shift the modulator aside and remove an arm of its fastening.
10. Liberate from clamps on the forward party of the power unit submitting and returnable hydraulic tubes and disconnect them from the liquid pump (the Uniform hydraulic system see the Head). At once закупорьте the open ends of tubes in order to avoid hit in dirt system.
11. Отболтите a regulator of hydraulic pressure and the distributor of giving of a hydraulic liquid from a forward part of the power unit also tie up them aside a wire, or lay on a prop. Disconnect from transmission all hydraulic tubes.
12. Give штуцерную a nut of fastening of a directing tube measuring probeа to the pallet картера to transmission, turn out a bolt of fastening of a tube to картеру АТ and lift the receiver.
13. Disconnect electroconducting from the gauge-switch of the permission of start/fires of a backing and (at a corresponding complete set) from a casing of a drive of a speedometer. Give a fixing nut () / a bolt () and disconnect from картера transmissions the tyre () grounding.
14. By means of clips or clamps press both hoses brought to cooler ATF. Loosen the fixing collars also disconnect hoses from cooler assemblage. Prepare for gathering of a spilt cooling liquid. Rinse cold assemblage of a cooler and surfaces adjoining to it.
15. Turn out screws of fastening of a cover of a cable of a drive of a gear change to the basic arm. Accurately disconnect a tip of a cable from the spherical hinge on the lever of a choice of transfers on transmission.

Do not suppose change of position of the lever of a choice of transfers after a detachment drive a cable! As an additional safety measure mark lever position rather картера transmissions. Moving back along a cable, liberate it from intermediate clamps and take aside from transmission.

16. Disconnect the core drive a cable of inclusion of a mode kick-down from a cam of the case of a throttle, then ослабьте counternuts and liberate a cover of a cable from a basic arm. Liberate a cable from intermediate clamps and directing, having provided possibility of its unobstructed removal together with transmission.
17. Turn out fixing bolts and remove a plate of the bottom cover drive a disk for the purpose of providing of access to bolts of fastening of the converter of rotation. Turn out the bolt opened to access, then turn a cranked shaft for a bolt of its pulley, providing access to the following. Operating in a similar manner, give all three bolts of fastening of the converter to приводному to a disk.
18. Fix the rotation converter in transmission by means of a metal strip, приболченной to one of apertures for starter fastening.
19. Take a rubber fixing finger and disconnect a cable of a drive of a speedometer from приводной assemblages. Liberate a cable from intermediate clamps and directing. On the models equipped with the gauge of speed, disconnect corresponding electroconducting.
20. Remove power shafts (Power shafts see the Head).
21. Prop up the engine a jack (for the purpose of loading distribution lay between a head of a jack and the pallet картера wooden брусок). Alternatively, hang out the engine with the help лебедки or a cross-section beam.
22. Through wooden брусок поддомкратьте transmission.
23. Give the central nut of the left support of the power unit, remove a washer. Give two fixing nuts (do not forget about washers) and remove a rubber pillow of a support.
24. Remove the remote plug, then turn out a fixing hairpin of a support from картера transmissions and remove it together with a washer (in case of need take advantage for a hairpin reversing of a special ex-tractor).
25. Completely having accepted on a jack transmission weight, turn out bolts of its fastening картера to the engine. Try to remember adjusting position of each of bolts and arms fixed by them. Once again make sure that nothing disturbs to transmission extraction.
26. Shift a jack to the left, removing transmission from directing pins.
27. Lower a jack and take transmission from under the car. Take freely planted directing pins and clean them in a reliable place.