Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes

12. A suspension bracket and a steering
THE GENERAL DATA

Details of a forward suspension bracket
1 – the left rack of a forward suspension bracket,
2 – a cover,
3 – a nut of fastening of a rod
The shock-absorber,
4 – a nut of fastening of a rack,
5 – the top support of a rack,
6 – a washer,
7 – the top plate of a spring,
8 – the directing plug,
9 – амортизирующее a ring,
10 – a spring,
11 – a protective casing,
12 – a nut,
13 – the shock-absorber,
14 – a place of fastening of steering draught,
15 – a rotary fist,
16 – a brake board,
17 – a lock ring,
18 – the bearing,
19 – a nave,
20 – a brake disk,
21 – a nut of fastening of a power shaft,
22 – a support,
23 – the spherical hinge of the bottom lever,
24 – a nut of fastening of the spherical hinge,
25 – a clip of the bottom lever,
26 – the back plug of the bottom lever,
27 – the bottom lever,
28 – an arm,
29 – the plug,
30 – шарнирный a bolt of the bottom lever,
31 – a bolt of fastening of the stabilizer of cross-section stability,
32 – draught of the stabilizer of cross-section stability,
33 – the stabilizer of cross-section stability,
34 – fastening of the stabilizer of cross-section stability,
35 – a clip of fastening of the stabilizer of cross-section stability,
36 – a power shaft

Details of a back suspension bracket
1 – the shock-absorber,
2 – a spring,
3 – the shock-absorber (Hatchback),
4 – a spring,
5 – a nut of a nave,
6 – a persistent ring,
7 – the external bearing,
8 – a nave,
9 – the internal bearing,
10 – a sealing ring,
11 – a pin of a nave,
12 – the longitudinal lever of a back suspension bracket,
13 – the plug of fastening of a back beam,
14 – the back stabilizer of cross-section stability,
15 – rubber гаситель fluctuations

The independent forward suspension bracket of type Mac-Pherson includes cylindrical springs and compound telescopic shock-absorbers. Racks Mac-Pherson fasten to the bottom cross-section levers of a suspension bracket by means of spherical hinges. On rotary fists wheel bearings, brake supports and naves are established. On the majority of models the forward stabilizer of cross-section stability is established

At such design of a forward suspension bracket course stability of the car increases at braking and drift when one party of the car moves on a slippery surface, and another – on a firm covering is excluded.

The back suspension bracket of dependent type consists from back торсионной a beam and longitudinal levers with бочкообразными springs and telescopic shock-absorbers. On models 2,0 of l with 16th valves the back stabilizer of cross-section stability is established.

On some models mechanically adjustable self-levelled back suspension bracket is established.

On cars steering transfer реечного type is established. For turn of forward wheels steering transfer incorporates to racks of a forward suspension bracket steering draughts.

On some models the steering amplifier is established. The drive of the pump of the amplifier of a steering is carried out by a belt from a pulley of a cranked shaft.


On the main page