Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes

12.11. Removal and installation of a back beam Removal

PERFORMANCE ORDER
1. Loosen the bolts of fastening of back wheels, then lift a back part of the car and fix on supports.
2. Remove back wheels.
3. On models with system of a self-levelled back suspension bracket remove pressure in system.
4. Disconnect a cable of a manual brake from the jack and release it from fastenings on the car bottom.
5. Remove a back part of an exhaust system from rubber pillows.
6. Disconnect a back brake hose from an arm of a back beam and close hoses stoppers.
7. On models the Versatile person and the Van unscrew bolts, fastening an arm of a spring of the valve of adjustment of pressure.
8. Remove springs of a back suspension bracket.
9. A jack through wooden брусок support the central part of a back beam.
10. Disconnect forward fastening (the nut and bolt arrangement is specified by arrows) longitudinal levers of a back suspension bracket from the bottom of the car and lower a jack together with a back beam.
11. Move a cable of a manual brake on an exhaust system and remove a back beam.
12. At installation of a new back beam rearrange on it elements of brake system, a nave, the stabilizer of cross-section stability and other hinged details.

Installation

PERFORMANCE ORDER
1. With the assistant establish a back beam on the car, thus move a cable of a manual brake on an exhaust system.
2. Insert bolts of fastening of a back beam, but do not tighten them definitively at this stage.
3. Establish springs and fix shock-absorbers.
4. Connect back brake hoses and pump over hydraulic system of brakes.
5. On models the Versatile person and the Van, moving an arm, adjust a tension of the spring operating the valve of adjustment of pressure.
6. Fix an exhaust system on rubber pillows.
7. Fix a cable of a manual brake on the bottom of the car and connect it to the jack.
8. Adjust bearings of back wheels.
9. Adjust back brakes for what press not less than 10 times a brake pedal, then adjust a manual brake.
10. Establish wheels, then lower the car on the earth and tighten bolts of fastening of wheels.
11. Load the car, having planted on forward sitting of two persons, then tighten bolts of fastening of a back beam the demanded moment.
12. On models with a self-levelled back suspension bracket increase in system pressure to 0,8 bar.


On the main page