Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes

12.18. Removal and installation of tips of steering draught
THE GENERAL DATA
The prevention

At removal of a tip of steering draught it is necessary to use a stripper of spherical hinges. At installation it is necessary to use new самоконтрящуюся a nut of fastening of the spherical hinge of a tip of steering draught.

Removal

PERFORMANCE ORDER
1. At presence remove a wheel cap, then ослабьте bolts of fastening of a forward wheel.
2. Tighten a manual brake, then lift a forward part of the car and fix on supports.
3. Remove a corresponding forward wheel.
4. Loosen the a bolt clamping a tip of steering bent for to a carving regulator of steering draught.
5. Unscrew самоконтрящуюся a nut, крепящую the spherical hinge of a tip of steering bent for to a rack of a forward suspension bracket.
6. Using a stripper of spherical hinges, take a pin of the spherical hinge of a tip of steering draught from a rack of a forward suspension bracket.
7. Using a paint or a sticky tape, note an arrangement of a tip of steering draught on a carving regulator. Also it is possible to count number of coils of a carving on an acting part of a carving regulator.
8. Unscrew a tip from steering draught. The tip of the right steering draught is marked by letter R, and the tip of the left steering draught has no marks.

Installation

PERFORMANCE ORDER
1. Screw a tip of steering draught on a carving regulator in the same position, as before removal.
2. Establish a pin of the spherical hinge of a tip of steering draught on a rack of a forward suspension bracket and fix new самоконтрящейся a nut, having tightened its demanded moment.
3. Tighten a bolt clamping a tip of steering draught.
4. Establish a wheel and lower the car on the earth.
5. Tighten bolts of fastening of a wheel the demanded moment.
6. Check up and, if necessary, adjust corners of installation of forward wheels.


On the main page