Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes

12.8. Replacement of the back shock-absorber
THE GENERAL DATA

The top fastening of the back shock-absorber

And – without system of a self-regulated back suspension bracket,

In – with system of a self-regulated back suspension bracket or with two counternuts,

Х = 9 mm,

Y = 6 mm

The prevention

Removal of shock-absorbers is necessary for making by turns. Replacement of shock-absorbers make in pairs on one axis of the car.


SEDAN AND HATCHBACK

PERFORMANCE ORDER
1. Working in a luggage space, uncover, closing the top fastening of the shock-absorber.
2. Unscrew a nut of the top fastening of the shock-absorber, thus keep a rod of the shock-absorber from проворачивания the second wrench. Remove a washer and a rubber element of the top fastening of the shock-absorber.
3. Lift a back part of the car and fix on supports.
4. At presence, working under a back part of the car, disconnect from the shock-absorber an air pipe of system of a self-levelled back suspension bracket.
5. A jack support the corresponding lever of a back suspension bracket. Unscrew a bolt (it is specified by an arrow), крепящий the bottom part of the shock-absorber to the longitudinal lever of a back suspension bracket.
6. Manually compress the shock-absorber and take it from the longitudinal lever of a back suspension bracket.
7. Take the shock-absorber from under the car and remove a rubber element of the bottom fastening of the shock-absorber and a cup from the top part of the shock-absorber.
8. Using киянку, establish the bottom fastening of the shock-absorber in an arm.
9. Screw in a bolt of the bottom fastening of the shock-absorber and tighten its demanded moment.
10. Partially lower the car, thus establish the top fastening of the shock-absorber into place.
11. Lower the car on the earth, then establish a rubber pillow and a washer of the top fastening of a rod of the shock-absorber.
13. Tighten a nut of fastening of a rod of the shock-absorber so that the shock-absorber rod acted, as is shown in fig. the Top fastening of the back shock-absorber.
14. Establish a cover.
15. Similarly replace the second back shock-absorber.
16. On models with a self-levelled back suspension bracket increase in system pressure to 0,8 bar.

THE VERSATILE PERSON AND THE VAN

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports.
2. At presence, working under a back part of the car, disconnect from the shock-absorber an air pipe of system of a self-levelled back suspension bracket.
3. A jack support the corresponding lever of a back suspension bracket. Unscrew a nut and remove a washer and a rubber pillow of the bottom fastening of the shock-absorber. Lower a jack.
4. Unscrew a bolt (it is specified by an arrow) the top fastening of the shock-absorber and remove the shock-absorber.
5. At installation fix the top part of the shock-absorber a bolt, having tightened it at this stage by hand.
6. Fix the bottom part of the shock-absorber. Thus check up correctness of an arrangement of a rubber pillow and a washer and tighten a nut of the bottom fastening of the shock-absorber the demanded moment.
7. Tighten a bolt of the top fastening of the shock-absorber the demanded moment.
8. Similarly replace the second back shock-absorber.
9. On models with a self-levelled back suspension bracket increase pressure in system to 0,8 bar.


On the main page