Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   - 12.4. The bottom lever of a forward suspension bracket
      12.4.1. Removal and installation of the bottom lever of a forward suspension bracket
      12.4.2. Replacement of plugs of the bottom lever of a forward suspension bracket
      12.4.3. Replacement of the spherical hinge of the bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes

12.4. The bottom lever of a forward suspension bracket

12.4.1. Removal and installation of the bottom lever of a forward suspension bracket Removal

PERFORMANCE ORDER
1. At presence remove a wheel cap, then ослабьте bolts of fastening of a wheel.
2. Tighten a manual brake, then lift a forward part of the car and fix on supports.
3. Remove a corresponding wheel.
4. Unscrew a nut, крепящую the end of the stabilizer of cross-section stability to the bottom lever.
5. Take шплинт and unscrew корончатую a nut (it is specified by an arrow) the spherical hinge connecting the bottom lever of a forward suspension bracket from a proof forward suspension bracket.
6. Using a stripper of spherical hinges, take a pin of the spherical hinge from a rotary fist.
7. Unscrew шарнирные bolts and bolts (are specified by arrows), fastening a clip of the bottom lever of a forward suspension bracket and remove the lever.

Installation

PERFORMANCE ORDER
1. Using a corresponding tap, clear a carving in apertures under bolts of fastening of a clip of the bottom lever.
2. Establish the bottom lever of a forward suspension bracket on the car and fix bolts, having tightened them at this stage by hand. The head шарнирного a bolt should settle down from the forward party of the car.
3. Screw on шарнирный a bolt new самоконтрящуюся a nut.
4. Before ввинчиванием a bolt of fastening of a clip of the bottom lever put on a carving of bolts the means interfering their unscrewing.
5. Support the bottom lever of a forward suspension bracket a jack in horizontal position and tighten all bolts of fastening of the bottom lever the demanded moment.
6. Lower a jack.
7. Establish a pin of the spherical hinge of the bottom lever in a rotary fist and fix a nut, having tightened its demanded moment. Using new шплинт, fix a nut from unscrewing.
8. Connect the stabilizer of cross-section stability to the bottom lever.
9. Establish a wheel and lower the car. Tighten bolts of fastening of a wheel and, at presence, establish a wheel cap.
10. Check up and, if necessary, adjust corners of installation of forward wheels.


On the main page