Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system and release
   - The power supply system - petrol models
      Removal and installation of assemblage of an air cleaner
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Neetilirovannoe fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvanie pressure in the power supply system
      Removal and installation of the fuel pump
      Removal and installation of the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of system Bosch Motronic 5.1
      Removal and installation of components of system Magneti-Marelli 8Р
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + The power supply system - diesel models
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of the fuel pump

Before the beginning of performance of procedure attentively familiarise with preventions the Power supply system - petrol models has undressed!

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. For the purpose of providing of access to pump assemblage lift a back seat (address to the Head the Running gear and a steering) and unbend a carpet covering in the right part of back passenger branch.

3. A screw-driver accurately hook and remove from the floor panel a plastic cover of access to assemblage of the fuel pump.



4. Disconnect from assemblage of the pump electroconducting and glue the pump an adhesive tape to кузовной panels that it casually has not failed for a petrol tank.

5. Mark and disconnect the hoses of giving brought to the pump and fuel return. If hoses fasten collars of braided type, cut off them and at assemblage replace more practical screw or worm. Right after detachments закупорьте the open ends of hoses in order to avoid hit in dirt system.

6. Remember mutual position of landing labels on assemblage of the pump and a fixing ring. Turn away a ring and remove it from a fuel tank. For отворачивания rings rest a screw-driver against cross-section ledges on its face surface and strike to the handle not strong blows, turning a ring counter-clockwise until there will be a possibility отворачивания it manually.

7. Having uncovered, release clamps and separate the pump from the basis of a fuel tank. Take assemblage from a tank. Try not to damage the mesh filter and not to spill fuel on painted кузовные surfaces and a salon upholstery. Remove a rubber sealing ring, - at assemblage it is subject to replacement without fail.
8. Replaceable fuel pumps are delivered only in gathering and to regenerative repair are not subject.

Installation

 PERFORMANCE ORDER

1. Make sure of serviceability of a condition, passableness and reliability of fastening of the filter in the basis of assemblage of the pump. Lay on the regular place on a petrol tank a new sealing ring.
2. Accurately get pump assemblage on the regular place in a petrol tank and latch it in the basis of the last.
3. Achieve label combination on a cover of assemblage with central of three labels on a fuel tank, then establish and strongly tighten a fixing ring. Make sure of correctness of combination of labels of a ring, a pump and tank cover.
4. Connect to unions of the pump hoses of giving and fuel return (be verified with the marks put in the course of dismantle). Track reliability of fixing of hoses fixing collars.
5. Connect electroconducting.
6. Connect a negative wire to the battery and start the engine. Check up on presence of signs of leaks unions of both hoses brought to the pump.
7. If everything is all right, establish into place a plastic cover of access and return in a starting position a back seat (address to the Head the Running gear and a steering).


On the main page