Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system and release
   - The power supply system - petrol models
      Removal and installation of assemblage of an air cleaner
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Neetilirovannoe fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvanie pressure in the power supply system
      Removal and installation of the fuel pump
      Removal and installation of the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of system Bosch Motronic 5.1
      Removal and installation of components of system Magneti-Marelli 8Р
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + The power supply system - diesel models
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of a fuel tank

Removal

 PERFORMANCE ORDER

1. Before removal the tank is necessary for devastating completely. As drain stopper it is not provided, to start tank removal is better after all fuel will be developed. The rests can be pumped out through a jellied mouth manually (preliminary disconnect a negative wire from the battery).
2. Поддомкратьте a back of the car also establish it on props. Remove the right back wheel.
3. Remove intermediate section of system of release of the fulfilled gases with the muffler (Systems of decrease in toxicity and release of the fulfilled gases see).
4. Отболтите also remove from the bottom of the car a thermofilter.
5. Отболтите bearing скобу a fuel tank.
6. Take a lock finger and disconnect from приводную draught from the back proof-reader of height of a road gleam. Take the proof-reader aside.
7. Without disconnecting, remove covers from the hydraulic tubes located under the bottom.
8. Liberate hydraulic tubes from clamps on the bottom of a fuel tank.
9. Liberate the fuel filter from the arm and take him aside.
10. Remove a mudguard of an arch of the right back wheel and disconnect from rubber tubes of a line of giving and fuel return.
11. Loosen the collars also disconnect from a fuel tank a jellied mouth and ventilating hoses.
12. Get under a tank тележечный a jack (for loading distribution lay between a head of a jack and the tank bottom wooden брусок). Cock a jack, having accepted on it petrol tank weight.
13. Turn out bolts of fastening of a tank and, slightly having handed over to the right, приопустите a tank on a jack.
14. Where it is required, disconnect electroconducting from an active hydraulic suspension bracket.
15. Wring out a plastic uvula and disconnect electroconducting from the fuel filter.
16. Release collars and disconnect hoses from assemblage топливозаборника.
17. Lower a fuel tank and take it from under the car.
18. If inside there are firm adjournment or a moisture, take from it assemblage of a gasoline pump with топливозаборником and wash out a tank pure gasoline. The tank represents the integral tank made by a method of blowing from a synthetic material and in case of serious mechanical damage is subject to replacement. Nevertheless, in certain cases insignificant leaks can be eliminated by performance of special repair procedures, - consult at experts of car-care centre.

Installation

Installation is made upside-down. The special attention should be turned for following moments:
   a) At tank installation on the car track, that no hoses have appeared clamped between a tank and the car bottom.
   b) Track correctness of a lining and reliability of connection of all lines and hoses.
   c) Before to connect приводную bent for to the proof-reader of height of a road gleam, translate a control lever an active suspension bracket in position LOW.
   d) In summary fill in in a tank a small amount of pure fuel and check up it on presence of signs of leaks, having driven away the car on a road roadside.


On the main page