Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system and release
   - The power supply system - petrol models
      Removal and installation of assemblage of an air cleaner
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Neetilirovannoe fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvanie pressure in the power supply system
      Removal and installation of the fuel pump
      Removal and installation of the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of system Bosch Motronic 5.1
      Removal and installation of components of system Magneti-Marelli 8Р
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + The power supply system - diesel models
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal, installation and adjustment of a cable of gas

Removal


Knot of fastening of a cable of gas to the throttle case (to model with РКПП)


Knot of fastening of a cable of gas to the throttle case (to model with АТ)

 PERFORMANCE ORDER

1. In an impellent compartment disconnect the core of a cable of gas from the throttle case, extend a cable from the rubber plug of an arm through passage and remove a spring clamp (illustrations Knot of fastening of a cable of gas to the throttle case (to model with РКПП) and Knot of fastening of a cable of gas to the throttle case (to model with АТ see)).
2. Moving back lengthways on a cable, liberate it from intermediate directing clamps and обвязок. Try to remember a route of a lining of a cable.
3. Release clamps and remove section of the bottom felt furnish under the panel of devices from the driver's party of the car.
4. In car salon release a clamp of a cover of the assembly block of safety locks, having turned it on a turn quarter counter-clockwise. Uncover the assembly block the panel of devices.
5. Release a clip and disconnect the core of a cable from the top part of a pedal of gas.
6. Liberate a cover of a cable from the holder on a pedal arm. Tie up by the end of a cable a string piece.
7. Return to an impellent compartment and liberate the rubber plug of a cable through passage from a back partition. Then, having pulled a cable on itself, involve it in an impellent compartment. Untie from a tip a string and leave its passed through a partition.
8. Attentively examine a cable, checking it on presence of signs of deterioration or mechanical damages. Also check up a condition of the rubber plug through passage. Defective components replace.

Installation

 PERFORMANCE ORDER

1. Tie up a cable to a string and involve it through a partition in car salon. Untie from a tip a string and latch a cable cover in the holder of an arm. The core connect to the pedal end.
2. Check up reliability of fastening of a cable and landing in a partition of the rubber plug through passage. Establish into place the felt panel of furnish of the panel of devices and a cover of the assembly block of safety locks.
3. Having returned to an impellent compartment, make sure of correctness of landing of a cover of a cable in the plug through passage, then, moving along a cable and watching correctness of a route of a lining, fix it in all intermediate clamps and обвязках.
4. Put on a flat washer a tip of a cable and establish a spring clamp.
5. Pass a cable cover in the plug of an arm through passage on the throttle case. The cable core connect to a cam of a drive throttle заслонки. Make cable adjustment (see more low).

Adjustment

 PERFORMANCE ORDER

1. In an impellent compartment remove a spring clamp from a cover of a cable of gas. Make sure that the drive cam заслонки is pressed to an emphasis. Smoothly pull a cable from the plug through passage, completely having chosen a core weak point.
2. Having fixed a cable in the given position, establish a spring clamp in last from open flutes in front of the rubber plug through passage. After installation of a clip and отпускания covers, the weak point of the core of a cable should appear very insignificant.
3. Ask the assistant to squeeze out a pedal of gas and make sure that the drive cam passes in the extreme position corresponding to full opening заслонки. At release pedals the cam should come back smoothly in a starting position, nestling on an emphasis.
4. On models with АТ, having finished with a gas cable, check up adjustment drive a cable of inclusion of a mode kick-down (Automatic transmission see).


On the main page