Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   - 12.16. A steering column
      12.16.1. Removal and installation of a steering column
      12.16.2. Repair of a steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   + 12.19. Steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes





12.16.2. Repair of a steering column
THE GENERAL DATA

Elements of a steering column without adjustment of an angle of slope

1 – the button of a sound signal,
2 – a steering wheel,
3 – knot of a cam,
4 – a spring,
5 – the switch of illumination and turns,
6 – the switch стеклоомывателя and a screen wiper,
7 – the holder of switches,
8 – the bearing,
9 – the bottom casing of a steering column,
10 – a steering shaft,
11 – an aligning plastic washer,
12 – a pipe of a steering column,
13 – the cylinder of the lock of ignition,
14 – the lock of ignition,
15 – a casing of the lock of ignition,
16 – safety locks of the holder of switches,
17 – the top casing of a steering column

PERFORMANCE ORDER
1. Remove a steering column from the car.
2. Using a screw-driver edge as the lever, release clamps of a casing of the lock of ignition, then turn a casing counter-clockwise and remove it from a steering column.
3. For removal of the bearing from a casing of the lock of ignition release two clamps of the bearing and, using tubular оправку, established on an external ring of the bearing, beat out the bearing. At installation of the new bearing check up that the persistent washer and a fixing spring are correctly established.
4. Unscrew screws with a secret head and remove a casing of the lock of ignition. Do not remove simultaneously the switch and the cylinder of the lock of ignition to keep their relative positioning.
5. If the steering column is established in the car, unscrew top tightening a bolt of fastening elastic муфты to a steering shaft.
6. Take a steering shaft from a steering column.
7. Temporarily establish a plastic centering washer in the bottom part of a pipe of a steering column.
8. Establish a steering shaft in a pipe of a steering column.
9. If the steering column is established in the car, connect a steering shaft with elastic муфтой and screw in top tightening a bolt of fastening elastic муфты, but do not tighten it definitively.
10. Will put the lock of ignition and fix its screws with a secret head.
11. Establish a casing of the lock of ignition with new clamps.
12. If the steering column is established in the car, move a steering shaft upwards against the stop and tighten tightening a bolt of fastening elastic муфты.
13. Check up that forward wheels of the car are established in position for movement directly forward, and the top bolt of fastening elastic муфты is located in horizontal position.
14. The further assemblage is made in sequence, return dismantling.
15. Establish a steering wheel.

On the main page