Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
- 3.1. 4-cylinder engines
3.1.1. Specifications
3.1.2. Repair kinds, выполняемыe without removal of the engine from the car
3.1.3. Installation of the piston of 1st cylinder in ВМТ a compression step
3.1.4. A cover of a head of cylinders
3.1.5. A soaking up collector
3.1.6. A final collector
3.1.7. Cam-shafts and pushers
3.1.8. A head of cylinders
3.1.9. A cover of a chain drive of cam-shafts
3.1.10. A forward epiploon коленвала
3.1.11. The oil pallet
3.1.12. The oil pump
3.1.13. A flywheel (a leading disk of the hydrotransformer)
3.1.14. A back epiploon коленвала
3.1.15. Engine mount details
+ 3.2. Engines V6 of 3,0 l (1993-1994) and 3,4 l (since 1995)
+ 3.3. Dismantle and engine major repairs
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes
|
Details of the oil pump
1. The pump (a chain cover)
2. The reduktsionnyj valve
3. Springs
4. A plate
5. A lock ring |
6. An epiploon коленвала
7. A pump cover
8. A leading rotor
9. A conducted rotor
10. A lining |
Removal
| PERFORMANCE ORDER |
| 1. Remove belts and a roller натяжителя. |
| 2. Remove the pallet. |
| 3. Remove a pulley коленвала. For access to редукционному to the valve uncover chains. |
|
4. Turn away 9 screws (указны arrows) and remove the case of the oil pump. |
| 5. Remove from demountable planes of the pump and the block of cylinders the consolidation rests, wash out planes solvent. |
| 6. Get leading and conducted rotors. |
| 7. Cautiously disassemble редукционный the valve. |
|
Check
| PERFORMANCE ORDER |
| 1. Wash out all details in solvent, check up presence of deterioration and damages. |
| 2. Check up a condition of a sliding surface of the piston редукционного the valve and a spring. At detection of damages the piston complete with a spring replace. |
|
|
3. Check up probeом a backlash between a conducted rotor and the case. |
|
4. Check up probeом a face backlash of a rotor between a rotor and a cover. |
|
5. Check up probeом a backlash in gearing of leading and conducted rotors. |
| 6. Results of measurements compare to the standard. If backlashes exceed norm rotors in the complete set replace. If necessary replace the pump case (a chain cover). |
|
Installation
| PERFORMANCE ORDER |
| 1. Oil rotors for the engine and establish in the case. |
|
|
2. Put in a pump cavity technical vaseline, lay a lining, put a cover and tighten screws. |
| 3. Grease the piston редукционного the valve with fresh oil for the engine and establish valve details. |
| 4. Establish a new lining of a cover of a chain on directing pins. |
| 5. Establish a chain cover, having entered the platen of a leading rotor of the oil pump into gearing with a leading gear wheel коленвала. |
| 6. Establish other details upside-down. |
| 7. Fill in oil, start the engine, be convinced of absence of leaks. |
|
|
On the main page
|