Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. 4-cylinder engines
      3.1.1. Specifications
      3.1.2. Repair kinds, выполняемыe without removal of the engine from the car
      3.1.3. Installation of the piston of 1st cylinder in ВМТ a compression step
      3.1.4. A cover of a head of cylinders
      3.1.5. A soaking up collector
      3.1.6. A final collector
      3.1.7. Cam-shafts and pushers
      3.1.8. A head of cylinders
      3.1.9. A cover of a chain drive of cam-shafts
      3.1.10. A forward epiploon коленвала
      3.1.11. The oil pallet
      3.1.12. The oil pump
      3.1.13. A flywheel (a leading disk of the hydrotransformer)
      3.1.14. A back epiploon коленвала
      3.1.15. Engine mount details
   + 3.2. Engines V6 of 3,0 l (1993-1994) and 3,4 l (since 1995)
   + 3.3. Dismantle and engine major repairs
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes

3.1.3. Installation of the piston of 1st cylinder in ВМТ a compression step
THE GENERAL DATA
The prevention

It is meant that works are carried out at correct installation of the distributor of ignition (if the distributor is provided). If it is necessary to redeem correct position of the distributor define an engine step on sensation of a compression in 1st cylinder at the turned out candle then combine labels of the moment of ignition (see more low).

Installation of the piston of 1st cylinder in ВМТ a compression step is necessary for performance adjusting and наладочных works (adjustment of valves, installation of the moment of ignition, etc.).

PERFORMANCE ORDER
1. Translate the selector in position Neutral or Park (on а/т) or in neutral position (on a manual transmission). Disconnect sockets from the ignition coil (coils).
System of ignition with the distributor
2. On a wire from a candle of 1st cylinder (or under the applied scheme) find a corresponding conclusion to a cover of the distributor of ignition and designate риской on the case. Uncover the distributor.
3. Turn коленвал a key for a head of a bolt of a pulley clockwise before combination risks on a pulley коленвала with a label "0" on a motionless scale.
4. If the index бегунка the distributor is opposite risks on the distributor case the piston of 1st cylinder is in ВМТ a compression step. If бегунок it is turned on 180 ° from risks turn коленвал on 1 turn then the piston of 1st cylinder will be exposed in ВМТ a compression step.
5. Thus labels on a scale and a pulley should be combined, and the index бегунка should be opposite the risks, 1st cylinder designating a conclusion.
6. Designate conclusions of other wires according to an engine operating procedure. Turning коленвал further clockwise concerning position ВМТ of 1st cylinder, it is possible to expose in ВМТ the piston of each cylinder, combining the index бегунка with labels of conclusions.
System of ignition without the distributor (engines of 1998)
7. Turn out a candle of 1st cylinder and attach a compression measuring instrument through a hose in length about 150 mm, having screwed the hose union in an aperture for a candle.
8. Turn коленвал until then while pressure of a compression will not start to raise in process of rapprochement of labels on a pulley and on a scale. Having passed labels, remove a measuring instrument and turn долее коленвал on 2 turns.
The prevention

The most exact installation of the piston in ВМТ a compression step on such engines is reached by simultaneous combination of labels on a pulley коленвала and on asterisks of cam-shafts (subsection 3.1.7 see).


On the main page