Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
- 8. Brake system
   8.1. Specifications
   8.2. ABS-system
   8.3. Колодки disk brakes
   8.4. A brake support
   8.5. A brake disk
   8.6. Колодки drum-type brakes
   8.7. The wheel cylinder of back brakes
   8.8. The main cylinder of brakes
   8.9. Hoses and hydrodrive tubes
   8.10. A pressure regulator
   8.11. A manual brake
   8.12. Cables of a manual brake
   8.13. The vacuum amplifier of brakes
   8.14. Prorolling of brakes
   8.15. Adjustment of a pedal of a brake
   8.16. The switch of a signal of braking
+ 9. A suspension bracket and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes





8.6. Колодки drum-type brakes
THE GENERAL DATA

The prevention

Колодки vary only in the complete set on one axis.


Back brake of the car "Toyota 4 Runner/Hilux/Surf"

1. A cutting spring washer
2. A crank ркучного brakes
3. A cover
4. The union for prorolling
5. A cover
6. The piston
7. A spring
8,11. A regulator
9. A piston cuff
10. The cylinder
12. A spring
13. Back колодка
14, 16, 26. A cutting washer
15. Clamp cups Pads
17. A lining
18. A drum
19. The lever of automatic adjustment колодок
20. The conducted lever of a manual brake
21. A clamp spring Pads
22. A lobby колодка
23. A cable
24, 28. A pin
25. Заглушка
27. A spring

Details of the lever of a regulator

1. Колодка

2. The conducted lever of a manual brake

3. A cutting washer

4. The regulator lever

5. A cutting lock washer
Replacement
PERFORMANCE ORDER
1. Release nuts of wheels, lift a back part of the car. Remove back wheels.
2. Remove a drum. If the drum does not give in to removal fill in between hairpins of a flange of a semiaxis and drum apertures a getting liquid and обстучите a drum from the inside on a contour. As a last resort displace a drum, in regular intervals wrapping bolts in special carving apertures.
3. If to removal disturb Pads get заглушку from a board of a brake and reduce Pads. For this purpose take away from a cogwheel the lever of a regulator and rotate a cogwheel of a regulator a screw-driver counter-clockwise.
4. Clear a brake of a dust and a dirt. Check and replacement колодок carry out according to applied pictures.
5. Disconnect a spring from a lobby Pads.
6. Remove a clamping spring of a lobby Pads having pressed a cup and having turned on 90 .
7. Remove the bottom spring.
8. Remove a clamping spring back Pads.
9. Disconnect a spring of the lever of a regulator.
10. Disconnect a small cable of a crank.
11. Remove a regulator.
12. Get a cutting lock washer of an axis of the lever of a regulator from back Pads.
13. Get a cutting washer from an axis of the lever of a manual brake.
14. Beat out an axis from old Pads and запрессуйте in new (if the axis is absent).
15. Having established the lever on an axis new Pads, compress a cutting washer.
16. Establish the lever of a regulator and fix a new cutting washer. Establish a spring.
17. Grease a rubbing surface Pads with refractory greasing. Clear and grease a mobile part of an adjusting hairpin.
18. Disconnect a regulator and a spring.
19. Establish the collected lever on a board of a brake and fix, having established a pin, a spring, a basic washer and a cup.
20. Attach the bottom spring.
21. Establish колодку, having entered it into gearing with a regulator.
22. Dress a coupling spring on another колодку.
23. Fix колодку a clamping spring.
24. Clear a drum and check up a surface condition. Check up ovality of a drum, at strong damages a drum pierce. If after проточки diameter appears more limiting, a drum replace.
25. Execute these actions for a brake of other wheel.
26. Adjust a crank of a manual brake (1 – a spring, 2 – шплинт, 3 – an axis). For this purpose disconnect a cable. Displace a crank in a direction And against the stop in колодку (a backlash In = 0).
27. Release a counternut and rotating a bolt, establish S.Zatjanite's backlash a counternut. Attach a spring and a cable. Execute adjustment for other wheel.
28. Be convinced. That the regulator hairpin rotates, moving the lever of a manual brake in salon.
29. Establish drums. Press some times a brake pedal. Then dissolve Pads before contact with a drum, rotating a screw-driver a regulator cogwheel through an aperture in a brake board. Take away Pads that the drum could rotate freely a little. Establish заглушку.
30. Further assemblage is carried out upside-down. Check up pedal position. If the pedal is too close to a floor moving a backing press some times a brake pedal to adjust a backlash between колодками and drums by means of an automatic regulator (works only at movement by a backing).

On the main page