Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
- 9. A suspension bracket and a steering
   9.1. Specifications
   9.2. Springs and shock-absorbers (racks) of a forward suspension bracket
   9.3. The stabilizer of a forward suspension bracket
   9.4. A rotary fist
   9.5. A forward nave and the bearing
   9.6. Spherical support
   9.7. The top lever
   9.8. The bottom lever
   9.9. Back shock-absorbers
   9.10. The back stabilizer of cross-section stability
   9.11. A cross-section bar of the back bridge
   9.12. Back springs
   9.13. Longitudinal bars of the back bridge
   9.14. A steering wheel
   9.15. A tip of steering draughts
   9.16. A cover of the steering mechanism
   9.17. The steering mechanism
   9.18. The hydraulic booster pump
   9.19. The wheel hydraulic booster
   9.20. Corners of installation of forward wheels
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes





9.6. Spherical support
THE GENERAL DATA

Nave, rotary fist and the top support of the car "Toyota 4-Runner/Hilux/Surf"

1. A cover
2. A collar
3. A lock ring
4. The top support
5. A fist
6. The bearing
7. A nave
8. An epiploon
9. A lock ring
10. A brake board
11. The gauge of speed of ABS-system
12. The dividing plug (for а/м with ABS-system)
13. An epiploon (all-wheel drive а/м)
14. A cap (rear-wheel а/м)

The bottom support of the car "Toyota 4-Runner/Hilux/Surf"

1. The bottom support
2, 4. Шплинт
3. Steering draught
5. The bottom lever
6. A fist

Check люфта in the bottom spherical support

 
1. No more than 2,3 mm

Check

Condition of spherical support it is necessary to check each time at car lifting.

PERFORMANCE ORDER
1. Lift car redock.
2. Clear support and check up a condition of sealants.
3. Raise the car, having substituted a jack under the bottom lever of a suspension bracket to unload a support.
4. Shake a wheel mount, simultaneously checking люфт in a support (it is carried out with the assistant). If люфт considerable a support replace (see fig. Check люфта in the bottom spherical support).
5. Shake the top support. Replace a support if it is found out considerable люфт.
6. The support should be checked at each removal of a fist or support.
7. For check try to turn a support finger by hand.
8. If the finger is turned by hand a support replace.
9. The manufacturer more exact way is recommended.
10. Shake a finger of a support from itself and on itself 5 times then turn a nut.
11. A Dinamometrichesky key with a scale in some Н.м. Check up the resistance moment проворачиванию a finger.
12. Turn a finger a key, doing 1 turn for 2–4 seconds On 5th turn check up indications of the moment and compare with standard (subsection 9.1 see).
13. If the moment differs from norm a support replace.

Replacement of the top support

PERFORMANCE ORDER
1. Remove a fist.
2. Remove a collar, a cover and get a lock ring.
3. Выпрессуйте a support a stripper through оправку (1 – deep оправка).
4. If the hinge, запрессуйте with its hydraulic press through 2 оправки is replaced
(1 – оправка).
5. Further assemblage is carried out upside-down.
6. All fastenings of a suspension bracket tighten with the set moment.

Replacement of the bottom support

PERFORMANCE ORDER
1. Disconnect steering draught.
2. Disconnect a fist from the bottom lever.
3. Turn away bolts and remove the bottom support.
4. Establish a new support and tighten bolts with the set moment.
5. Further assemblage is carried out upside-down.

On the main page