Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
- 12. A suspension bracket and a steering
   12.1. A technical characteristics
   + 12.2. A rack of a forward suspension bracket
   12.3. Replacement of the bearing of a forward wheel
   + 12.4. The bottom lever of a forward suspension bracket
   12.5. Removal and installation of the forward stabilizer of cross-section stability
   12.6. Adjustment of the bearing of a back wheel
   + 12.7. A nave of a back wheel
   12.8. Replacement of the back shock-absorber
   + 12.9. The back stabilizer of cross-section stability
   12.10. Replacement of back springs
   12.11. Removal and installation of a back beam
   12.12. Replacement of the plug of the longitudinal lever of a back suspension bracket
   12.13. Replacement of elements of a back suspension bracket with sheet springs (Pickup)
   12.14. Check of system of a self-levelled back suspension bracket
   12.15. Removal and steering wheel installation
   + 12.16. A steering column
   12.17. Replacement of the cylinder of the lock and contact group of the lock of ignition
   12.18. Removal and installation of tips of steering draught
   - 12.19. Steering transfer
      12.19.1. Replacement elastic муфты a shaft of steering transfer
      12.19.2. Replacement of protective casings of steering transfer
      12.19.3. Removal and installation of the shock-absorber of steering transfer
      12.19.4. Removal, repair and installation of steering transfer
   12.20. Removal of air from system of a steering with the amplifier
   12.21. Removal and installation of the pump of the amplifier of a steering
   12.22. Removal and installation пополнительного a tank of hydraulic system
   12.23. Corners of installation of forward wheels
+ 13. A body
+ 14. Electric schemes





12.19.4. Removal, repair and installation of steering transfer
THE GENERAL DATA

STEERING TRANSFER WITHOUT THE STEERING AMPLIFIER

Centering of steering transfer

And = 325 mm

Removal

PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. On models with the carburettor remove the air filter.
3. On models with a washer of headlights release a tank of a washer and move it aside.
4. Using a screw-driver edge as the lever, remove fixing plate from heads of bolts, крепящих steering bent for to steering transfer, then unscrew bolts and remove washers and a plate.
5. If steering transfer has the shock-absorber, unscrew bolts, fastening a clip of steering transfer and remove the shock-absorber.
6. Establish steering transfer to position for movement directly forward.
7. Unscrew two tightening bolts, крепящих elastic муфту and move elastic муфту to a steering shaft.
8. Remove the right forward wheel.
9. In a motor compartment unscrew bolts, fastening two clips of steering transfer to a partition of a motor compartment, then on the right side take steering transfer.
10. Keep in mind that on some models wires can be attached to steering transfer and hoses which before removal of steering transfer are necessary for disconnecting.

Repair

It is independently possible to replace only protective covers of steering transfer, spherical hinges of cross-section steering draught and cross-section steering draughts.

Installation

PERFORMANCE ORDER
1. Establish steering transfer on a partition of a motor compartment and fix its new bolts, having tightened their demanded moment.
2. Before connection elastic муфты check up that steering transfer is in position for movement directly forward (And = 325 mm) (fig. Centering of steering transfer see).
3. Establish into place elastic муфту and fix its bolts.
4. Connect steering draughts with gear рейкой, thus establish under them washers.
5. Establish a plate or an arm of the shock-absorber and tighten bolts the demanded moment.
6. At installation it is necessary to use a new fixing plate which is established on heads of bolts of fastening of steering draughts.
7. The further installation is made in sequence, return to removal.

STEERING TRANSFER WITH THE STEERING AMPLIFIER

Removal

PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. On models with the carburettor remove the air filter.
3. On models with a washer of headlights release a tank of a washer and move it aside.
4. Disconnect hoses on the left side of steering transfer and close a hose and an aperture for a hose suitable stoppers.
5. Using a screw-driver edge as the lever, remove fixing plate from heads of bolts, крепящих steering bent for to steering transfer, then unscrew bolts and remove washers and a plate.
6. If steering transfer has the shock-absorber, unscrew bolts, fastening a clip of steering transfer and remove the shock-absorber.
7. Establish steering transfer to position for movement directly forward.
8. Unscrew two tightening bolts, крепящих elastic муфту and move elastic муфту to a steering shaft.
9. Remove the right forward wheel.
10. In a motor compartment unscrew bolts, fastening two clips of steering transfer to a partition of a motor compartment, then on the right side take steering transfer.
11. Keep in mind that on some models wires can be attached to steering transfer and hoses which before removal of steering transfer are necessary for disconnecting.

Installation

PERFORMANCE ORDER
1. Establish steering transfer on a partition of a motor compartment and fix its new bolts, having tightened their demanded moment.
2. Before connection elastic муфты check up that steering transfer is in position for movement directly forward.
3. Establish into place elastic муфту and fix its bolts.
4. Connect steering draughts with gear рейкой, thus establish under them washers.
5. Establish a plate or an arm of the shock-absorber and tighten bolts the demanded moment. At installation it is necessary to use a new fixing plate which is established on heads of bolts of fastening of steering draughts.
6. The further installation is made in sequence, return to removal.
7. Fill in a fresh liquid in hydraulic system of the amplifier of a steering and remove from system air.

On the main page