Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
- 3. Maintenance service
   - 3.1. Maintenance service of cars with petrol engines
      3.1.1. Operational materials and liquids
      3.1.2. Refuelling capacities
      - 3.1.3. Periodicity of service
         - 3.1.3.1. Each 15 000 km
            3.1.3.1.1. Replacement of oil and the oil filter
            3.1.3.1.2. Replacement of spark plugs
            3.1.3.1.3. Check of tightness of hoses and вытекания liquids
            3.1.3.1.4. Check and replacement auxiliary drivers belts
            3.1.3.1.5. Check of system of ignition
            3.1.3.1.6. Adjustment of turns of idling and quality of a mix
            3.1.3.1.7. Clearing of the filter of the fuel pump on models with the carburettor
            3.1.3.1.8. Level check трансмиссионной liquids
            3.1.3.1.9. Check of a condition of oil
            3.1.3.1.10. Electroconducting check
            3.1.3.1.11. Check brake колодок and a brake disk
            3.1.3.1.12. Adjustment of a manual brake
            3.1.3.1.13. Exhaust system check
         + 3.1.3.2. Each 30 000 km
         + 3.1.3.3. Each two years
         + 3.1.3.4. Each 60 000 km
   + 3.2. Maintenance service of cars with diesel engines
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

3.1.3.1.5. Check of system of ignition MODELS WITH SYSTEM OF IGNITION WITH THE BREAKER

PERFORMANCE ORDER
1. Replace contacts of the breaker and adjust a backlash and duration of the closed condition of contacts of the breaker as it is described in subsection 8.1.3. After adjustment put one or two drops of engine oil in the centre of dredging of a cam, and a cam grease with technical vaseline. Put only a greasing small amount, otherwise greasing can get on breaker contacts.
2. Check up a condition of high-voltage wires.
3. Mark the high-voltage wires going to spark plugs, and remove them from spark plugs, having pulled for a tip, instead of for a wire.
4. Check up an internal surface of a candle tip on absence of corrosion which represents a white powder. Establish a candle tip on a spark plug before its accurate fixing. In the absence of accurate fixing, using flat-nose pliers, draw in a spring clamp in a candle tip.
5. Using pure rags, clear high-voltage wires of a dirt and greasing. Check up high-voltage wires on presence прожогов, cracks and other damages. Do not bend and do not stretch a high-voltage wire as the internal conductor of a wire can be broken off.
6. Remove the second end of a high-voltage wire from a cover of the distributor of ignition. Wire removal make only for a tip. Examine an internal part of a tip on presence of corrosion which represents a white firm powder. Check up density of landing of a tip of a high-voltage wire on a cover of the distributor of ignition. In the presence of an ohmmeter check up resistance of a high-voltage wire. Establish a high-voltage wire on a cover of the distributor of ignition before its accurate fixing.
7. Similarly check up other high-voltage wires.
8. In need of replacement of high-voltage wires get high-voltage wires only for your car and the engine.
9. Uncover the distributor of ignition and clear it. Check up a cover condition on presence of cracks, carbonaceous paths, deterioration, and also on обгорание and deterioration of contacts. Check up a condition of the central coal contact and freedom of its moving in a cover.
10. Remove a rotor of the distributor of ignition and check up it on presence of cracks and обгорания. At replacement of high-voltage wires it is recommended to replace also a cover and a rotor of the distributor of ignition. Installation of a rotor of the distributor of ignition is necessary for making so that it was accurately fixed on a distributor shaft.
11. Unstable start of the engine can take place at moisture hit on elements of system of ignition. For an exception of it put on elements of system of ignition water-repellent means.

MODELS WITH CONTACTLESS SYSTEM OF IGNITION

At work on system of ignition it is necessary to be careful with the included ignition, as it is possible to receive blow by a current from a high-voltage part of system of ignition. People with stimulators of warm activity are not recommended to check and make repair of system of ignition. Switch off ignition before a detachment or connection of any element of system of ignition or probeов the measuring device.

PERFORMANCE ORDER
1. Check up a condition of high-voltage wires and elements of the distributor of ignition in the same way, as well as on models with system of ignition with the breaker of contacts.
2. Check up installation of a corner of an advancing of ignition (the corresponding description in subsection 8.2.4 see).


On the main page