Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
- 11. An electric equipment
   11.1. Specifications
   11.2. The battery
   + 11.3. Ignition system
   11.4. The coil () ignitions
   11.5. The ignition distributor
   11.6. Check and installation of the moment of ignition
   11.7. The block of electronic ignition
   11.8. The induction gauge
   + 11.9. System of a charge of the battery
   + 11.10. The generator
   11.11. System of start-up of the engine
   + 11.12. The starter electric motor
   11.13. The traction relay
   11.14. Pressure check
   11.15. Short circuit detection
   11.16. Check of reliability of grounding
   11.17. Check of integrity of a chain
   11.18. A finding of not closed chain
   11.19. Search of malfunctions
   11.20. Safety locks
   11.21. Fusible crosspieces
   11.22. Breakers
   11.23. The relay
   11.24. The breaker of indexes of turn / of the alarm system
   11.25. The switch of indexes of turn
   11.26. The lock of ignition and a lock drum
   11.27. The switch of external illumination
   11.28. The screen wiper switch
   11.29. Lamps of headlights
   11.30. Adjustment of headlights
   11.31. The headlight case
   11.32. Replacement of lamps
   11.33. The receiver and dynamics
   11.34. The aerial
   + 11.35. The screen wiper electric motor
   11.36. The switch of heating of back glass
   11.37. A heater of back glass
   11.38. A guard of devices
   11.39. A sound signal
   11.40. The electric drive of mirrors
   11.41. Cruise-control
   + 11.42. The electric drive window lifterа
   11.43. The electric drive of door-locks
   11.44. Safety pillows
+ 12. Electroschemes

11.34. The aerial
THE GENERAL DATA
The prevention

On a part of cars "Toyota 4 Runner/Hilux/Surf" the printing aerial is established, all works on which service are carried out in car-care centre.

Removal and installation
PERFORMANCE ORDER
1. Remove the receiver and disconnect штеккер. Disconnect all latches and скобы on an aerial line. Attach to the aerial a wire (cord) in length about 1,5 m.
The stationary aerial
2. Turn away an aerial mast.
3. Turn away a basis nut, disconnect the basis and extend a cable so that the auxiliary wire has seemed.
4. Attach to a cable of the new aerial a wire and involve a cable.
5. Installation is carried out upside-down.
The aerial with the electric drive
The prevention

Works are carried out together.
6. Translate the ignition key in position LOCK.
7. Turn away a nut of the basis of the aerial.
8. Operating simultaneously (together with the assistant), press buttons AM/FM of the receiver and translate the ignition key in position АСС, – during this moment it is necessary to keep the aerial. The aerial will be put forward and completely leaves from лебедки the electric motor. Remove a mast, the ignition key should be in position АСС still.
9. Remove three latches (are specified by arrows) internal panel of a wheel niche in an aperture between a wheel and a wing, get the panel, disconnect a socket.
10. Turn away a bolt of fastening and remove the aerial electric motor.
11. Attach to a cable of the new aerial a wire and involve a cable in salon.
12. Establish the electric motor.
13. Establish an aerial mast so that a teeth on a cable has been turned forward.
14. Wind a cable and involve a mast, for what translate the ignition key in position LOCK (if the key has already been translated in this position from position АСС execute actions (see item 8). If the cable is not taken up, повращайте it in an arrow direction.
15. Wrap a basis nut even if the mast completely was not involved. Press buttons of a choice of ranges on the receiver and the aerial will be involved.
16. Further installation is carried out upside-down.


On the main page