Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation

Тойота 4Раннер
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. A suspension bracket and a steering
+ 10. A body
- 11. An electric equipment
   11.1. Specifications
   11.2. The battery
   + 11.3. Ignition system
   11.4. The coil () ignitions
   11.5. The ignition distributor
   11.6. Check and installation of the moment of ignition
   11.7. The block of electronic ignition
   11.8. The induction gauge
   + 11.9. System of a charge of the battery
   + 11.10. The generator
   11.11. System of start-up of the engine
   + 11.12. The starter electric motor
   11.13. The traction relay
   11.14. Pressure check
   11.15. Short circuit detection
   11.16. Check of reliability of grounding
   11.17. Check of integrity of a chain
   11.18. A finding of not closed chain
   11.19. Search of malfunctions
   11.20. Safety locks
   11.21. Fusible crosspieces
   11.22. Breakers
   11.23. The relay
   11.24. The breaker of indexes of turn / of the alarm system
   11.25. The switch of indexes of turn
   11.26. The lock of ignition and a lock drum
   11.27. The switch of external illumination
   11.28. The screen wiper switch
   11.29. Lamps of headlights
   11.30. Adjustment of headlights
   11.31. The headlight case
   11.32. Replacement of lamps
   11.33. The receiver and dynamics
   11.34. The aerial
   + 11.35. The screen wiper electric motor
   11.36. The switch of heating of back glass
   11.37. A heater of back glass
   11.38. A guard of devices
   11.39. A sound signal
   11.40. The electric drive of mirrors
   11.41. Cruise-control
   + 11.42. The electric drive window lifterа
   11.43. The electric drive of door-locks
   11.44. Safety pillows
+ 12. Electroschemes

11.5. The ignition distributor

The ignition distributor

1. A cover
2. Бегунок
3. A cover
4. The distributor case
5. The coil
6. The condenser
7. The induction gauge
8. A dustproof booth

Removal and installation
1. Disconnect the battery from weight.
2. Disconnect sockets from the distributor.
3. Find on a cover a label of a conclusion of 1st cylinder. If the label on a cover is absent, find a corresponding conclusion on a wire from 1st cylinder.
4. Uncover the distributor, turn коленвал and establish бегунок opposite to a conclusion of 1st cylinder.
5. Put a label on bottom the distributor case directly under the index бегунка (it is specified by an arrow).
6. Designate also position of the case of the distributor on a head of cylinders (it is shown by arrows).
7. If fastening by two bolts with заплечиками for a flange release these bolts (to provide a free wheeling of a shaft of the distributor) is provided but completely do not turn on.
8. Turn away a bolt of fastening of the distributor, then submit the distributor in a horizontal direction and get it. Turn коленвала after distributor removal is not supposed. If коленвал nevertheless turned, establish the piston of 1st cylinder in ВМТ a step of compression and сориентируйте бегунок and the distributor case.
9. Combine sample on a gear wheel of the distributor with a flute on the case.
10. Insert the distributor into the engine, it is exact сориентировав the case on the put labels.
11. If the distributor is not established in a place once again check up the labels put before dismantling. Establish the distributor precisely on these labels.
12. Wrap a bolt of fastening of the distributor.
13. Further installation is carried out upside-down.
11. Check up installation of the moment of ignition (subsection 11.6 see), tighten a fastening bolt.

On the main page